background image

6.2   Working Mode:

6.2.1   Dehumidification Working Mode

M

ode 

Code

Function

Relay 

1

H04=0

Dehumidification

High fan speed

Medium fan speed

Low fan speed

Compressor

Air damper open

Relay 

2

Relay 

3

Relay 

4

Relay 

5

If the humidity of the air is higher than the setting, the fan turns on;5 seconds later,the compressor turns on

;

If the humidity of the air is lower than the setting, the compressor turns off;3 minutes later,the fan turns off.

The compressor 

should 

cycle on and off at an interval

 

more than 

3 minutes

.

6

.

2

.

2

  Description

Mode:the same before the power failure

§

The initial value as below:

Fan speed:High

§

6

.

3

  Initial Value

The controller has data memory function when there is power failure.

Air damper:close

§

6

.

4

  Fan Control

AC motor fan speed can be adjusted manually when H04=0:

§

EC motor (0~10V) fan has 5 fan speeds,which can be set separately.

§

F01=1,high fan speed available

§

F02=1,t

he fan turns off 3 minutes later 

after achieved the set humidity and temperature (only for the 

§

available system working mode)

F01=2,high fan speed & low fan speed available

§

High fan speed & low fan speed available when H04=1.

§

F01=3,high fan speed & medium fan speed & low fan speed available

§

Fan works according to F02 when achieve the set humidity and temperature (only for the available 

§

system working mode):

The initial value is high speed,can be adjusted manually.

§

F02=2,t

he fan 

keeps working after achieved the set humidity and temperature (only for the available 

§

system working mode)

High fan speed available when H04=2.

§

Open or close air damper automatically when H01=1:

§

Air damper close when the unit is powered off manually.

§

6

.

5

  Air Damper Control

Air damper works according to H01,R03 when the unit is turned on manually.

§

Open or close air damper manually when H01=0:

§

Air damper close:100% return air

§

Air damper open:mixed fresh and return air

§

Indoor humidity ≧ R03:air damper close;Indoor humidity≦R03~R04:air damper open.

§

Can switch to manual mode from automatic mode and works manually for 30 minutes amd continue to 

§

work automatically.

21

22

Summary of Contents for DEH-10K




















Reviews: