background image

Cabinet-type  dehumidification  equipment  adopts  direct  evaporative  cooling  design,  which  can  dry  the  air 

under atmospheric pressure. The dehumidification equipment can dehumidify the air with a temperature range of 

5°C to +35°C within 100% relative humidity.It is widely used in hotels, office buildings, hospitals, commercial and 

residential, scientific research institutions and other places.

The cabinet-type dehumidifier can work normally in the following temperature range.It will not work normally 

outside this range, which is not a quality problem of the equipment itself.

1.1  Application

Product drying

§

Business hotels.

§

This  manual  is  for  the  users  of  dehumidifiers,  including  installation,  operation,  maintenance,  and  

troubleshooting.

This  manual  introduces  cabinet-type  dehumidification  equipment.  The  dehumidification  air  volume  of  the system 

is 

3 500

m³/h--

10 000

m³/h, and the dehumidification capacity of the system 

is 300 L/day---1000 L/day

Villas

§

Scientific research institutions.

§

Museums and laboratories

§

Other wet areas

§

This equipment has a wide range of applications, such as:

1.2   Content

1

. General

Temp

Type

Dehumidify

Ventilate

Min

Max

DBT(°C)

Indoor

Ourdoor

Max

DBT(°C)

35

5

40

35

2

45

2

.

Unit

(Figure 1)
The internal circulation of the dehumidifier: through the operation of the compressor → discharge high 

temperature and high pressure gas from the exhaust port → enter the condenser for cooling → It becomes 
a low-temperature and high-pressure gas → intercepted by a capillary tube → becomes a low-temperature 
and low-pressure liquid → vaporizes and absorbs heat through an evaporator → back The compressor 
becomes a low-temperature and low-pressure gas.

(Figure 2)

External circulation of dehumidifier: It uses a refrigerator to dehumidify with a ventilation system. 

Compared with other dehumidification methods (heating dehumidification, ventilating dehumidification, 
adsorption dehumidification), it is characterized by stable , reliable, and continuous performance. The 
working principle is the fan draws warm & humid air through the refrigerated evaporator(cooling coil). The 
air is cooled well below its dew point: tempearature decreases and moisture removed.The water condenses 
on the cold surface of the evaporator and drips into a water container(and then flows by gravity into drain 
pipe) or is led directly to a drain. Then, the cold dry air continues through a hot condenser which heats it up 
and returns it to the room to pick up new humidity. This procedure is continued until the desired condition 
is achieved.

2.1  Introduction

The design of the dehumidifier meets the requirements of the IEC protection level IP 45.

2.2  Working Principle

compressor

 

condenser

fan

capillary

RH 

Temp.

 

humidity ratio

φ

t

d

t

C

φ(%)

dg/kg

F

igure

 

1

F

igure

 

2

1

2

Summary of Contents for DEH-3K




















Reviews: