background image

 

  

 

 

   

 

GIG-244CFX 

Order code: D2288  

7. LED INDICATOR COMPRESSOR 

The LED indicator will light up when compressing. 
 

8. LINE INPUT JACKS (CHs 17/18 and 19/20) 

The stereo channels consist of two line inputs (¼" jacks), one for the left and one for the right channel. The 
inputs are unbalanced (TS connectors). These channels can also be used as mono channels by 
connecting to the jack labeled “L” (left). 

 
9. LINE INPUT RCA (CHs 21/22 and 23/24) 

These are unbalanced stereo RCA pin jacks. 
NOTE: Where an input channel provides both a MIC input jack and a LINE input jack or a LINE input jack 
and RCA pin jack, you can only use one pair of jacks at a time but not both pairs at the same time. 
Please connect to only one jack on each channel. 
 

10. SWITCH LINE / USB 

With this button you can switch the source of channel 21/22 between LINE or USB port. 
 

11. SWITCH LINE/MEDIA PLAYER 

With this button you can switch the source of channel 23/24 between LINE or Media player. 
 

12. MEDIA PLAYER (Optional) 

You can control the Media player with this section. For more information about the Media player see 
chapter “Media player” on page 15. 

 
13. USB LAMP 

This USB port provides 5V/500mA to connect a dash light. 

 
14. PHONES 

This is the PHONES output to plug in your headphones. 

 

Elements section 2 

 

 

Summary of Contents for D2288

























Reviews: