background image

 

  

 

 

11 

   

 

GIG-164CFX 

Order code: D2287  

31. EQUALIZER 
 
HI 

The high-frequency range is processed with a shelving filter above 12 kHz. You can boost or cut the 
bands up to 15 dB. In the center position (0 dB), the equalizer has a flat response. 
 

HI MID 

The high mid control adjusts the high mid frequency range. This is a peak filter which boosts and cuts the 
frequencies centered at 3,0 kHz. You can boost or cut the bands up to 15 dB. In the center position  
(0 dB), the equalizer has a flat response. 
 

LOW MID 

The low mid control adjusts the low mid frequency range. This is a peak filter which boosts and cuts the 
frequencies centered at 500 Hz. You can boost or cut the bands up to 15 dB. When in center position  
(0 dB), the equalizer has a flat response. 
 

LOW 

The low-frequency range is processed with a shelving filter below 80 Hz. You can boost or cut the bands 
up to 15 dB. In the center position (0 dB), the equalizer has a flat response. 
 

32. BALANCE CONTROL. 

By using the balance control you can adjust the balance between the left and the right channel. If you 
use a mono source (input left mono) the control works as a panorama control and lets you change the 
input signal’s position within the stereo image. 
 

Elements section 4 

 

 

 

Summary of Contents for GIG-164CFX

























Reviews: