background image

Q u i c k   I n s t a l l a t i o n   G u i d e  

H B 5 1   H y b r i d   I n v e r t e r  

R e v . 1  

© 2 0 1 8   D a r f o n   E l e c t r o n i c s   C o r p .  

1   |   P a g e  

IMPORTANT SAFETY WARNINGS 

PLEASE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS ON THE UNIT AND THIS GUIDE BEFORE INSTALLING THE INVERTER. 
AND, STORE THIS USER MANUAL WHERE IT CAN BE ACCESSED EASILY. 

This manual is for qualified personnel. The tasks described in this manual should be performed by qualified personnel only. 

Safety Symbols 

 

WARNING. 

This indicates the risk of electric shock. The presence of high voltage levels may constitute a risk of injury or death to users 

and/or installers.

 

 

CAUTION. 

This indicates important information where failure to comply may result in safety hazards or cause damage to this product.

 

 

General Precautions 

 

CAUTION. 

Before installing and using this inverter, read all instructions and cautionary markings on the inverter and all appropriate 

sections of this guide. Installing this inverter by licensed electricians only.

 

 

CAUTION. 

Normally grounded conductors may be ungrounded and energized when a ground fault is indicated.

 

 

CAUTION. 

This inverter is heavy. It should be lifted by at least two persons for the safety.

 

 

WARNING.

 Authorized service personnel should reduce the risk of electrical shock by disconnecting AC, DC and battery power from 

the inverter before attempting any maintenance or cleaning or working on any circuits connected to the inverter. Turning off controls 
will not reduce this risk. Internal capacitors can remain charged for 5 minutes after disconnecting all sources of power. 

 

WARNING. 

Do not disassemble this inverter yourself. It contains no user-serviceable parts. Attempt to service this inverter yourself may 

cause a risk of electrical shock or fire and will void the warranty from the manufacturer

 

WARNING. 

To avoid a risk of fire and electric shock, make sure that existing wiring is in good condition and that the wire is not 

undersized. Do not operate the Inverter with damaged or substandard wiring.

 

 

WARNING. 

To reduce risk of fire hazard, do not cover or obstruct the cooling fans.

 

 

CAUTION. 

Do not install the Inverter if it has received a sharp blow, been dropped, or otherwise damaged in any way. If the Inverter is 

damaged, call for an RMA (Return Material Authorization).

 

 

CAUTION. 

This inverter is not allowed to operate in parallel. Do not parallel connect more than one unit in AC output connector. 

Otherwise, it will damage this inverter.

 

 

 

Manufactured by 

Darfon Electronics Corp. 
167 Shan-ying Road, Gueishan 
Taoyuan 333, Taiwan, (R.O.C.) 
Tel: +886 3 2508800 

USA Office 

Darfon America Corp. 
103A Pioneer Way 
Mountain View, CA 94041 
Tel: +1.650.316.6300 

For more information 

www.darfonsolar.com 
 

  
©2018 Darfon Electronics Corp. All rights reserved. All specifications are subject to change without prior notice. Darfon and the Darfon logo are trademarks of Darfon 
Electronics Corp. All other trademarks are the property of the respective owners. 
 
 

WHAT’S IN THE BOX 

 

 

1

5

4

2

3

Parts Description  

 

Qty 

1.

 

HB51 Inverter   

 

 1 

2.

 

Backplate  

 

 

 1 

3.

 

Bracket   

 

 

 2 

4.

 

Wood Screws   

 

 6 

5.

 

Self-drilling Screws  

 6 

Summary of Contents for HB51









Reviews: