background image

  

18 

REGULATORY COMPLIANCE 

Notice for FCC 

 

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 
(1) this device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation.  
Modifying the equipment without Monoprice's authorization may result in the equipment no longer 
complying with FCC requirements for Class B digital devices. In that event, your right to use the 
equipment may be limited by FCC regulations, and you may be required to correct any interference to 
radio or television communications at your own expense. 
This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur 
in a particular installation. If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver 
is connected. 

Summary of Contents for 43710




















Reviews: