background image

01787 370187  

|

  info@darouv.co.uk  

|

  

darouv.co.uk

7

Electrical
 
This unit must be installed by a qualified electrician.

The Saphir range is supplied with a standard, BS1363 
UK mains plug and should be connected to an 
earthed 220-240V, 50-60Hz, single phase and neutral 
supply, via a 3A fused socket.

The control box is provided with a trailing earth 
lead 

– this must be connected to the stud on the 

chamber body

. If the installation of the chamber has 

interrupted a water pipe, bond these together again.

If the UV lamp is switched off at any point wait for 
approximately 30 seconds for the electronics to 
discharge before switching it back on.

Volt Free Contact Connections 
( and Saphir Pro only)

A 4-way (3-ways plus earth) connector is supplied 
to mate to the control box volt-free contact socket. 
If required, a length of suitable three-core plus earth-
control cable should be used to wire between the 
connector and the remote equipment. A junction box 
may be required to make the connection.

No voltages are connected internally to the relay – 
this must be done via the cable plug. The relay drives 
when the lamp is working correctly.

The socket is capped if this feature is not used. 

See specifications, below, for relays ratings.

Connections

Terminal 1 - relay common. Connect to supply.

Terminal 2 - relay normally closed. Supply output 
when lamp has failed.

Terminal 3 - relay normally open. Supply output 
when lamp is OK. Connector Terminal 4 – earth. This 
terminal is bonded to earth inside the control box.

Indicators and Controls

The range has the following features:

•  

Switch to reset the internal hour counter (see 
maintenance, lamp replacement).

•  Three-way indicator display showing the status of 

the system.

•  Alarm to warn of lamp failure and end of lamp life, 

this can be temporarily silenced.

•  Volt-free contact output for remote display of lamp 

on indicator (see specification).

System Status

Power On

Lamp On

Lamp Status

Alarm

System operating correctly,  
lamp less than 11 months old

Green

Blue

Green

Off

System operating correctly,  
lamp between 11 and 12 months old

Green

Blue

Alternating 

Green & Red

Off

Lamp still operating,  
but more than 12 months old

Green

Blue

Red

Bleep on  

12-second interval

Lamp failed

Green

Off

Red

Bleep on  

3-second interval

Saphir Range

Summary of Contents for Saphir Series

























Reviews: