background image

dCS Scarlatti DAC

 User Manual 

Software Issue 1.2x 

 

August 2011 

  

 

 

Flename: Scarlatti DAC Manual v1_2x.docx 

Page 25

 English 

version

 

Limited Warranty 

General   

 dCS

 warrants this product against defects in materials and workmanship for a period of 3 years from 

the date the unit was originally shipped from 

dCS

. During the warranty period, 

dCS

 will repair or, at our 

absolute discretion, replace a faulty product. Warranty repairs must only be carried out by 

dCS

 or our 

authorised service agents. Please contact your dealer if your unit requires service. 

Your dealer should have completed on your behalf an 

Owner Registration

 form at the time of sale 

and returned it to 

dCS

. On receipt of the Owner Registration form, 

dCS

 will add your contact details to 

our customer database. 

dCS

 will use this information for warranty purposes only, we will not contact 

you directly for reasons relating to sales and marketing. 

This warranty applies to the original owner. 

 

Warranty Exclusions 

The Warranty does not cover wear and tear. 

The Warranty on this product will be void if: 

 

the product is misused in any way. 

 

any unauthorised modifications or repairs are carried out. 

 

the product is not used in accordance with the Operating Conditions stated in this manual

.

 

 

the product is serviced or repaired other than by 

dCS

 or our authorised service agents. 

 

the product is operated without a mains earth (or ground) connection. 

 

the unit is returned inadequately packed. 

 

dCS

 reserve the right to apply a service charge if a product returned for warranty repair is found to be 

operating correctly, or if a product is returned without a returns number being issued. 

This warranty covers parts and labour only, it does not cover shipping charges or tax/duty. 

Our dealers or distributors are NOT authorised to extend the terms of this warranty, 

dCS

 cannot accept 

responsibility for any attempt to do so. 

Products re-sold by 

dCS

 on a “used” basis may be subject to reduced warranty terms. 

 

Obtaining Service 

Should you encounter a problem, contact your authorised 

dCS

 dealer for advice, quoting the model, 

the full serial number, software version number, and giving a detailed description of the fault. Your 
dealer will advise you fully on actions that need to be taken. When returning a unit, the original 
packaging should be used to avoid transit damage. Replacement packaging sets may be purchased 
from 

dCS. 

During the Warranty period, there will normally be no charge for parts or labour. 

 

Operating Conditions 

 

The supply voltage must remain /-10% of the A.C. voltage specified on the back panel. 

 

The supply frequency must be in the range 49Hz to 62Hz. 

 

Ambient temperature range: 0

°

C (32

°

F) to 40

°

C (104

°

F), non-condensing. 

 

Do not install the unit near heat sources such as radiators, air ducts, power amplifiers or direct 
strong sunlight. 

 

If in doubt, the easy test is – the unit is happy to work anywhere a human is. 

 

Summary of Contents for DCS SCARLATTI DAC



























Reviews: