Data EOC Master CD7944N Product User Manual Download

Page: 5 / 18

Company Address: Room 601, Floor 6, Building F, Songbai Road 1008, Sunshine Community

，

Xili Street, Nanshan District, Shenzhen(518108)

Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)

Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506

Website: www.cdatatec.com

2.1.4 Network Device Installation

2.1.4.1 EOC Master Installation

The network equipment installation at the optical node mainly includes: EOC master

CD7944N , installation accessories (hanging buckle, etc.).

2.1.4.2 CD7944N Panel Interface and Indicators

2.1.4.3 CD7944N Panel Definition



EOC partial panel (Including two EOC modules)

Interface

Description

Usage

Ethernet port

4*10/100/1000Mbps adaptive ports Uplink connect MAN

COM port

4 *Cable mixed signal output ports User-to-Home cable connects to

EOC master COM port



EOC partial panel indicator definition (Including two EOC modules)

Indicator

Panel Label

Status

Description

Power led

PWR

Power is normal

Off

Power is off or power failure

CABLE signal led

CAB1-2

Terminal link established

Blinking

There is terminal communication

in the link



Built-in ONU module panel

Summary of Contents for EOC Master CD7944N



















Search results

Summary of Contents for EOC Master CD7944N

Reviews:

Related manuals for EOC Master CD7944N

Brands by name

Popular brands

Data EOC Master CD7944N, Product User Manual

Search results

Summary of Contents for EOC Master CD7944N

Reviews:

Related manuals for EOC Master CD7944N

Brands by name

Popular brands