background image

Copyright © 1998, Datalogic. 

This manual is copyrighted, with all rights reserved. Under the copyright laws, this manual may not, in whole
or in part, be copied, photocopied, reproduced, translated or converted to any electronic medium or
machine readable form without prior written consent of Datalogic.

Limited Warranty
Under all circumstances this manual should be read attentively, before installing and/or using the pro-duct.
In no event Datalogic will be liable for any direct, indirect, special, consequential or incidental damages
arising out of the use or inability to use this documentation or product, even if advised of the possibility of
such damages. In particular, Datalogic shall not be liable for any hardware, software, or data that is stored
or used with the product, including the cost of repairing, replacing or recovering the above. Datalogic
reserves the right to change parts of the device at any time without preceding or direct announcement to
the client. 

Datalogic reserves the right to revise this manual, and to make changes in the contents without obli-gation
to notify any person or entity of the revision or change. A serial number appears on the product. Make sure
that this official registration number has not been removed. It should be used whenever servicing by
Datalogic or an authorized Datalogic dealer is ne-cessary. 

Important 
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
EN55022, and with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the user’s manual, may cause harmful interference to radio
communications. Operation of the equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense. Any unauthorized
changes or modifications to this equipment could void the user’s authority to operate this equipment.  

For CE-countries:

- The Dll2020-wo is in conformity with the CE standards.

For USA & Canada:

- To be used with UL listed and CSA certified computers/POS systems. 
- À utiliser avec des ordinateurs/systèmes POS registrés UL/certifiés CSA.

Radio and television interference
Operation of this equipment in a residential area can cause interference to radio or television reception. This
can be determined by turning the equipment off and on. The user is encouraged to try to correct the
interference by one or more of the following measures:

• Re-orientate the receiving antenna
• Relocate the device with respect to the receiver
• Move the device away from the receiver
• Plug the device into a different outlet in order to have the device and receiver on different branch

circuits 

If necessary, the user should consult the manufacturer, an authorized Datalogic dealer or experienced
radio/television technician for additional suggestions. The booklet

"How to Identify and Resolve Radio-TV

Interference Problems"

, prepared by the Federal Communications Commission, can be of help. It can be

obtained from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004000003454. 

P/N A232001 September ’98

Summary of Contents for DLL2020-WO































Reviews: