background image

Setting Up the System

MX-U81 Hardware Guide

Datalogic S.r.l.

1-4

Setting Up the System

WARNING

: To avoid damage to your unit, 

never

 plug in or unplug any cables when the unit power is on. Always shut 

down the processor and turn off the power supply first before making any cable changes (see “Turning Off the System” on 
page 1-3).
NOTE: When a new processor is powered on the first time, a monitor, keyboard, and mouse must be connected to the pro-
cessor to approve the license agreement.

1. Familiarize yourself with the major system components as shown in this manual. 

2. Unpack and check all the equipment.

Relative Humidity (30 °C)

Operating: 10% to 90% (non-condensing)
Storage: 5% to 95% (non-condensing)

Vibrations
(EN60068-2-6)

2 to 8 Hz: 1.75 mm amplitude / 
9 to 200 Hz: 0.5 g

Shock resistance
(EN60068-2-27)

11 MS (15 G) 

Housing material

Galvanized plate, plastic

Mechanical protection (EN 
60529)

IP20

Weight

4.52 lb. (2.05 kg)

Minimum Impact Software 
Version Required

11.5.0

CPU

MX-U81: Intel® Core i7 2.3 GHz – quad core

System Memory

8 GB DDR3 RAM

Storage

128 GB SATA SSD (MLC)

Graphics

Intel® HD 3000 (1920x1200 resolution) - DVI

PCIe

1 x PCIe x8

Camera Interface
1 A Max per connection

4 x Dedicated USB 3.0 ports

Serial Communication

1 x RS-232 Serial port

Keyboard/Mouse

4 x USB 3.0 ports

Communication Connectivity

Supports Ethernet/IP, Modbus, TCP, PROFINET, and OPC

Network interface

2 x LAN ports 10/100/1000 Mbps Base-T

Technical Data

Summary of Contents for MX-U81



































































Reviews: