background image

MX-U81 Hardware Guide

Battery

2-9

Datalogic S.r.l.

Battery

WARNING

: Risk of explosion if battery is handled improperly or replaced by an incorrect type. Do not recharge, 

disassemble, or dispose of in fire. Lithium batteries are considered hazardous waste. Dispose of used batteries 
according to battery maker’s instructions or in accordance with applicable local regulations.

The lithium battery (CR2477N, 3 V, 950 mAh) powers the internal real-time clock (RTC). It is located behind the proces-
sor’s front cover. The battery has a limited service life and should be replaced at least every four years.

WARNING

: Power must be disconnected before replacing the battery.

To replace the battery

1. Disconnect the power supply to the processor.
2. Touch the housing or ground connection in order to discharge any electrostatic charge from your body.
3. Press down on the slot cover’s top clip to open the battery slot.
4. Do not hold the battery by its edges. Using the removal strip, carefully pull the battery out of its slot.
5. Insulated tweezers may be used to insert the new battery in the slot. Be sure the removal strip is in place to make 

the next battery replacement easier.

6. Reconnect the power supply to the processor.
7. Reset the date and time in the BIOS.

Battery Slot cover open

Processor Front View

Battery

Summary of Contents for MX-U81



































































Reviews: