background image

Serial Port

MX-U81 Hardware Guide

Datalogic S.r.l.

5-2

Serial Port

A standard serial cable is used to connect the Processor to the serial port on an external device (e.g. terminal, PLC, motion 

controller, data recorder). This may require using a null modem cable or adapter. The serial port does not support hard-
ware (CTS/RTS) or software (Xon/Xoff) data flow control. Impact software supports RS-232 communication protocol 
only. RS-485 is not supported.

Monitor/Panel

The monitor/panel port provides RGB, DVI, and SDL video signals. The processor requires a monitor and keyboard when 
it first starts, and to configure the system. A VGA cable (5 meters maximum) with the appropriate adapter can be used on 
this connector.

Display Port

The display port provides DVI and HDMI video signals.

USB Processor to Camera

A USB 3.0 cable is used to connect the MX-U81 Processor to the U-Series camera. (USB 3.0, Micro B screw lock/A, 3 m)

Pin Number

Signal Name

1

No Connection

2

Received Data (RxD)

3

Transmitted Data (TxD)

4

No Connection

5

Signal Ground (GND)

6

No Connection

7

Request To Send (RTS)

8

Clear To Send (CTS)

9

No Connection

9 Pin Male

(Pin Side)

Pin 1

Summary of Contents for MX-U81



































































Reviews: