This product is covered by one or more of the following patents.
European Patent 851,211 B1; 1,111,690 B1; 1,148,346 B1; 1,209,487 B1.
Italian Patent IT 1,321,772.
S5N-PL/ML SERIES
INSTRUCTION MANUAL
IEC 60825-1
“Caution –
use of controls or adjustments or performance of
procedures other than those specified herein may result in hazardous
radiation exposure
”
CONTROLS
OUTPUT LED (S5N-
PL/ML…B01/C01/F01)
The y ellow LED ON indicates that the N.O. (normally
open) output status is closed.
POWER ON LED
The green LED indicates that the sensor is operating.
TRIMMER (S5N-
PL/ML…B01/C01/F01)
The trimmer can be used to adjust sensitiv ity ; the
operating
distance
increases
turning
the
trimmer
clockwise.
WARNING: The trimmer rotation is limited to 270° by a
mechanical stop.
Do not apply excessive torque when adjusting (max 40
Nmm).
INSTALLATION
S5N-PL:
The sensor can be fixed by means of the M18x1 threaded body
through a
18 mm hole, using the specific washer and the two CH.24
nuts enclosed (1.5 Nm maximum tightening torque).
Alternatively, the sensor can be mounted through the two housing’s holes
using two screws (M3x22 or longer) and washer.
Amongst the various possible solutions, we suggest to choose the
combination that offers the best visibility of the signalling LEDs and the
easiest access to the trimmer.
22 mm nuts, h=8 mm, (2 Nm maximum tightening torque) are available to
guarantee an improved torque.
S5N-ML:
The sensor can be fixed by means of the M18x1 threaded body
through a
18 mm hole, using the two CH.24 nuts enclosed (22 Nm
maximum tightening torque).
For both plastic version and metallic version are
available various orientable fixing brackets to
ease the sensor positioning (please refer to the
accessories listed in the general catalogue).
The operating distance is measured from the
front surface of the sensor lens.
In case of lateral translation, the object must
move as indicated in the figure.
CONNECTIONS
The connections are compliant to the EN 60947-5-2 standard.
S5N-
PL/ML…B01/C01/F01
+
10 … 30 Vdc
N.C. OUTPUT
BROWN
1
WHITE
2
BLACK
4
BLUE
3
N.O. OUTPUT
0 V
S5N-
PL/ML…G00
+
10 … 30 Vdc
TEST +
BROWN
1
WHITE
2
BLACK
4
BLUE
3
NOT USED
0 V
M12 CONNECTOR
2
3
1
4
DIMENSIONS
24
=
N°.2 Ø3.8
4
=
2.5
=
4
=
3
.8
2
POWER ON LED
mm
10
Ø4
TRIMMER
OUTPUT LED
OUTPUT LED
POWER ON LED
57
42
24
G version
L
X
X1
M O D E L S
B/C/F version
67
43
34
L
X1
X
CABLE VERSION
=
2.5
4
4
TRIMMER
=
24
14.5
25
15
M
1
8
x1
14
3.5
M12
10
1.5
49
M
1
8
x1
10
M12
S50-PL VERSIONS
S50-ML VERSIONS
14.5
POWER ON LED
OUTPUT LED
POWER ON LED
OUTPUT LED
10
Ø4
CABLE VERSION
G version
57
38
L
X
67
43
B/C/F version
M O D E L S
L
X
TECHNICAL DATA
S5N-PL PLASTIC VERSIONS
S5N-ML METALLIC VERSIONS
Power supply:
10 … 30 Vdc (limit values)
Ripple:
2 Vpp max.
Current consumption
(output current excluded):
35 mA max. (mod.B01/C01/F01)
30 mA max (mod.G00)
Outputs:
N.O. and N.C.; PNP or NPN
(short-circuit protection)
Output current:
100 mA max.
Output saturation voltage:
2 V max.
Response time:
333
s
Switching frequency:
1,5 kHz
Indicators:
OUT PUT LED (YELLOW) (mod.B01/C01/F01) / POWER ON LED (GREEN)
Setting:
sensitivity trimmer (mod.B01/C01/F01)
Operating mode:
LIGHT mode on N.O. output / DARK mode on N.C. output (mod.C01)
DARK mode on N.O. output / LIGHT mode on N.C. output (mod.B01/F01)
Operating temperature:
-
10 … 50 °C
Storage temperature:
-
25 … 70 °C
Insulating strength:
500 Vac 1 min., between electronics and housing
Insulating resistance:
>20 M
500 Vdc, between electronics and housing
Operating distance (typical
values):
B01: 0.1…16 m on R2
C01: 0…35 cm
F01/G00: 0…60 m
Emission type:
RED LASER: Class 1 IEC 60825-1 (2014) (mod.B01/C01/G00)
Class 1 CDRH 21 CFR PART 1040.10 (mod.B01/C01/G00)
Max. power
1 mW; Pulse = 5
S;
= 645…660nm; Frequency
25 kHz
Ambient light rejection:
according to EN 60947-5-2
Vibrations:
0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6)
Shock resistance:
11 ms (30 G) 6 shock for every axis (EN60068-2-27)
Housing material:
PBT
Nickel plated brass
Lens material:
PMMA
Mechanical protection:
IP67 Metal versions type 1 enclosure
Connections:
2 m cable
4 mm / M12 - 4 pole connector
Weight:
75 g. max. cable vers./25 g. max. connector vers.
110 g. max. cable vers./60 g. max. connector vers.
AtEx 2014/34/EU
II 3D EX tc IIIC IP67 T 85°C
SETTING
Setting of S5N-
PL/ML…B01
Position the sensor and reflector on opposite sides.
Turn the sensitivity trimmer to the maximum position.
Moving the sensor both vertically and horizontally, determine the power
ON and OFF points of the OUTPUT LED and then mount the sensor in
the middle of the points defined.
If necessary reduce sensitivity in order to detect very small targets.
In order to improve alignment, repeat the procedure detailed above whilst
progressively reducing the sensitivity.
Setting of S5N-
PL/ML…F01/G00
Position the sensors on opposite sides.
Turn the sensitivity trimmer to maximum: moving the sensor both
vertically and horizontally, determine the power ON and OFF points of the
OUTPUT LED and then mount the sensor in the middle of the points
defined.
If necessary, reduce sensitivity using the trimmer, in order to detect very
small targets. In order to improve alignment, repeat the procedure
detailed above whilst progressively reducing the sensitivity.
Setting of S5N-
PL/ML…C01
Turn the sensitivity trimmer to minimum: the OUTPUT
LED is OFF.
Position the target to detect in front of the sensor.
Turn the sensitivity trimmer clockwise until the
OUTPUT LED turns ON
(Target detected state, pos.A).
Remove the target, the OUTPUT LED turns OFF.
Turn the sensitivity trimmer clockwise until the OUTPUT LED turns ON
(Background detected state, pos.B).
The trimmer reaches maximum if the background is not detected.
Turn the trimmer to the intermediate position C, between the two
positions A and B.
TEST FUNCTION (S5N-
PL/ML…G00)
The TEST input can be used to inhibit the emitter and verify that the
system is correctly operating.
The receiver output should switch when the test is activated while the
beam is uninterrupted.
The input activating voltage range is 10…30 Vdc.
Datalogic S.r.l.
Via S. Vitalino 13 - 40012 Calderara di Reno - Italy
T el: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.com
Helpful links at www.datalogic.com:
Contact Us,
Terms and Conditions,
Support
.
For information about the disposal of Waste Electrical
and Electronic Equipment (WEEE), please refer to the
website at
© 2018 - 2020 Datalogic S.p.A. and/or its affiliates
ALL RIGHT S
RESERVED.
Without limiting the rights under copyright, no part of this
documentation may be reproduced, stored in or introduced into a retrieval
system, or transmitted in any form or by any means, or for any purpose,
without the express written permission of Datalogic S.p.A. and/or its
affiliates. Datalogic and the Datalogic logo are registered trademarks of
Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. All
other trademarks and brands are property of their respective owners.
Datalogic reserves the right to make modifications and improvements
without prior notification.
826000373 Rev.D
MIN
MAX
A
B
C
CLASS 1 IEC 60825-1 (2014)
LASER PRODUCT
S5N-PL VERSIONS
S5N-ML VERSIONS
