Appendix J – General Purpose Input Output Port Applications
Class Series 2 Programmer’s Manual
265
Failure to properly configure the GPIO Port can result in damage to the printer and / or connected devices.
Applicator Interface Card (Type 2) GPI/O Port B Overview
Pin Number
Signal Name /
Direction
[1]
Jumper
Position
Function / Description
1
+5 VDC
JMP 11
Installed
P5VDC is used (.5 amp maximum).
Drawing more than .5 amps can cause unreliable printer operation.
Removed
+5VDC must be supplied.
2
Input 6
N/A
N/A
Programmed input function.
3
Input 3
N/A
N/A
Programmed input function.
4
Output 6
JMP 7
Installed: Pins 1 – 2
Programmed output function pulled-up to +5VDC.
Installed: Pins 2 – 3
Programmed output function pulled-up to +24VDC.
Removed
An external voltage via external pull-ups determine this level, not 30VDC.
5
Output 3
JMP 4
Installed: Pins 1 – 2
Programmed output function pulled-up to +5VDC.
Installed: Pins 2 – 3
Programmed output function pulled-up to +24VDC.
Removed
An external voltage via external pull-ups determine this level, not 30VDC.
6
Ground
JMP 10
Installed
Printer chassis is used.
Removed
Ground must be supplied.
7
Input 5
N/A
N/A
Programmed input function.
8
Input 2
N/A
N/A
Programmed input function.
9
Output 5
JMP 6
Installed: Pins 1 – 2
Programmed output function pulled-up to +5VDC.
Installed: Pins 2 – 3
Programmed output function pulled-up to +24VDC.
Removed
An external voltage via external pull-ups determine this level, not 30VDC.
10
Output 2
JMP 3
Installed: Pins 1 – 2
Programmed output function pulled-up to +5VDC.
Installed: Pins 2 – 3
Programmed output function pulled-up to +24VDC.
Removed
An external voltage via external pull-ups determine this level, not 30VDC.
11
+24 VDC
N/A
N/A
P24 VDC (1.5 amp maximum).
12
Input 4
N/A
N/A
Programmed input function.
13
Input 1
N/A
N/A
Programmed input function.
14
Output 4
JMP 5
Installed: Pins 1 – 2
Programmed output function pulled-up to +5VDC.
Installed: Pins 2 – 3
Programmed output function pulled-up to +24VDC.
Removed
An external voltage via external pull-ups determine this level, not 30VDC.
15
Output 1
JMP 2
Installed: Pins 1 – 2
Programmed output function pulled-up to +5VDC.
Installed: Pins 2 – 3
Programmed output function pulled-up to +24VDC.
Removed
An external voltage via external pull-ups determine this level, not 30VDC.
[1]
Signal directions are given relative to the printer.
Summary of Contents for A-Class
