background image

 

21 

 

Press <ON/OFF> switch and wait until all LED’s are off 

 

 

Plug the AC power adapter into the printer. Press <ON>; the green LED is illuminated 

and after about 20 seconds the LED should go off

 

 

If the amber LED is on, this will continue on through this test indicating that the 

battery is accepting a charge and that the charge circuit is ok. At the end of a 180 
minute charge cycle the LED will go off.

 

 

4.4  Battery and Safety Information 

The printer is powered by a 7.4V Li-Ion battery cartridge. 

 

Charging time in the printer is approximately 3.0 hours. 

 

Take the battery out of printer if storing the printer for long periods of time. 

 

The battery storage temperature is 40°F to 104°F (4°C to 40°C). Do not store a fully 
charged battery at temperatures greater than 104°F (40°C) for long periods of time – 

the battery may permanently lose charge capacity. 

 

The recommended temperature for charging is between 68°F (20°C) to 77°F (25°C). 

 

Be sure to use a fully charged battery before long or battery intensive printing 

sessions. Certain operations (for example, printing receipts with a lot of bar codes and 
graphics) drain the battery more quickly than others. 

 

Dispose according to your local regulations. Do not throw in trash.  

 

 

Do not disassemble, short circuit, heat above 80°C, or incinerate: the battery may 
explode. 

 
 

4.5  Recycling Batteries 

The Rechargeable Battery Recycling Corporation (RBRC) is a non-profit organization created 

to promote recycling of rechargeable batteries. For more information about how to recycle 
batteries in your area, visit 

www.rbrc.org

 

Summary of Contents for ANDES 3

































Reviews: