background image

 

 
 
  Page 4 

 

 Serial iBootBar  v090212d 

 

 

 

Important Safety Information 

 
When using this product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and 
injury to persons, including the following: 
 

Disconnect all power cords before servicing! 

 

1.  Read and understand all instructions. 

2.  Follow all warnings in the manual and marked on the product.  

3.  Unplug this product from the wall outlet before cleaning.  Do not use liquid cleaners or aerosol cleaners.  Use a damp cloth for cleaning. 

4.  Do not use this product in an outdoor environment or near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet 
basement, or near a swimming pool. 

5.  Do not place this product on an unstable cart, stand, or table.  The product may fall, causing serious damage to the product. 

6.  Slots and openings in this product and the back or bottom are provided for ventilation to protect it from overheating, these openings must not be 
blocked or covered.  The openings should never be blocked by placing the product on the bed, sofa, rug, or other similar surface.  This product 
should never be placed near or over a radiator or heat register.  This product should not be placed in a built-in installation unless proper ventilation 
is provided. 

7.  This product should be operated only from the type of power source indicated on the marking label.  If you are not sure of the type of power 
supply to your home, consult your dealer or local power company. 

8.  This product is equipped with a three wire grounding type plug, a plug having a third (grounding) pin.  This plug will only fit into a grounding type 
power outlet.  This is a safety feature.  If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet.  
Do not defeat the safety purpose of the grounding type plug.  Do not use a 3-to-2 prong adapter at the receptacle; use of this type adapter may 
result in risk of electrical shock and/or damage to this product. 

9.   Do not allow anything to rest on the power cord.  Do not locate this product where the cord will be abused by persons walking on it. 

10.  Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.  

11.  Never push objects of any kind into this product through slots as they may touch dangerous voltage points or short out parts that could result 
in a risk of fire or electrical shock.  Never spill liquid of any kind on the product. 

12.  To reduce the risk of electrical shock, do not disassemble this product, but take it to a qualified serviceman when some service or repair work 
is required.  Opening or removing covers may expose you to dangerous voltages or other risks.  Incorrect re-assembly can cause electric shock 
when the appliance is subsequently used.  

13.  Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: 

a)  When the power supply cord or plug is damaged or frayed. 

b)  If liquid has been spilled into the product. 

c)  If the product has been exposed to rain or water. 

d)  If the product does not operate normally by following the operating instructions.  Adjust only those controls, that are covered by the operating 
instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to 
restore the product to normal operation. 

e)  If the product has been dropped or has been damaged. 

f)  If the product exhibits a distinct change in performance. 

14.  Avoid using a telephone (other than a cordless type) during an electrical storm.  There may be a remote risk of electric shock from lightning. 

15.  Do not use the telephone to report a gas leak in the vicinity of the leak. 

16.  Do not exceed the maximum output rating of the auxiliary power receptacle. 

 

Summary of Contents for sBB-N15





















Reviews: