DataTale AT-S111 User Manual Download | Manualshive

Page: 8 / 14

background image

8

ASSEMBLING THE SATA 2.5” HDD ENCLOSURE

To begin using the DataTale Mobile 2.5” SATA HDD Enclosure Kit, simply
install a 2.5” SATA hard drive in the Enclosure and complete the assembly
steps outlined below:

1. Firmly push the lid down from front to back and open the Enclosure. After

the lid is opened, the PCBA board (Printed Circuit Board) should be
securely in place inside the Enclosure. One package containing the two
HDD screws and two case screws should be attached.

2. Carefully take out the PCBA board from the enclosure. Align the SATA

connector of the hard drive with the PCBA board. Carefully insert the SATA
connector into the slot on the PCBA board until it’s firmly connected.

«
...
6
7
8
9
10
...
»

Summary of Contents for AT-S111















Reviews:

No comments

Related manuals for AT-S111

Brand: ZALMAN Pages: 11

Brand: MVP Pages: 19

GAGE104U40 Series

Brand: RAIDAGE Pages: 6

Brand: Rosslare Pages: 3

Brand: Rosslare Pages: 3

Brand: Carlon Pages: 4

Brand: Technologic Systems Pages: 9

Brand: V7 Pages: 11

Brand: Azio Pages: 7

Brand: AzenX Pages: 9

Brand: CRU Dataport Pages: 2

InFusion IMPE-2-IC Series

Brand: Vantage Hearth Pages: 6

Brand: Icy Box Pages: 27

EZ-Swap MRK-103F

Brand: Vantec Pages: 3

SuperSpeed NexStar 3

Brand: Vantec Pages: 15

Brand: Encore Pages: 4

Brand: Hamlet Pages: 12

Brand: Manhattan Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands