background image

Datatool is a brand of Scorpion Automotive Ltd 

Scorpion House, Drumhead Road, Chorley North Business Park, Chorley, Lancashire, England. PR6 7DE 

Tel: +44 (0) 1257 249928 E mail: 

info@datatool.co.uk 

Web: http://www.datatool.co.uk 

DT201 Operation Guide Revision 1 24-07-2023 

 

12 

 

8.

 

Press either button  on the first remote control to be  added, the DT201 will  bleep  once 
and the LED will flash once indicating the number of remote controls programmed.

 

 

NOTE: 

After programming the first remote control all other remote controls will be deleted. 

9.

 

Press either button on the following remote  controls to be added, the DT201 will bleep 
once  and  the  LED  will  flash  an  extra  flash  each  time  a  remote  control  is  programmed 
indicating the number of remote controls programmed.

 

 

10.

 

Turn off the ignition to exit programming and save the new settings. 

 

Technical Specification 

 

RF Device: 

433MHz, <1mW ERP 

Supply voltage range 

9VDC to 16VDC 

Supply current disarmed, no internal battery 
charge

 

3.1±0.2mA 

Maximum supply current disarmed or armed 
charging internal battery 

26mA±0.5mA 

Average supply current fully armed 

2.9mA±0.1mA 

Maximum supply current [long term storage 
mode] 

0.02mA 

Maximum directional indicator power per 
channel 

2 x 10W 

 
 
 
 
 
 
 
 
 
 
 
 

 
 

 
 

 

Battery Disposal Instructions: 
Battery should not be disposed of with general household 
waste. Bring damaged or worn out batteries to your local 
recycling centre or dispose of them in battery recycle 
bins that can be found in store. 

Keep batteries out 
of the reach of 
children. 

Summary of Contents for DT201
















Reviews: