Datavideo SE-2800 Instruction Manual Download | Manualshive

Page: 44 / 45

background image

44

Specification

( Below based on SE-2800 12 channel unit )

Inputs

• Maximum 12 inputs, can be configurable to

12 HD SDI, 12 SD SDI, 6 CVBS or 3 HDMI

• Possible combination, for example 10 HD SDI + 2 HDMI, or 3 HD SDI + 3 HDMI + 6 CVBS

Outputs

• 3 BNC output connectors for SDI Outputs
• 2 HDMI for Multiscreen
• RJ-45 for PC Remote controls
• 2 BNC for Sync-In and Sync-Out
• DB-9 for Console

Video Input

• HD/SDI: 1920 x 1080i/50, 1920 x 1080i/60
• SD: PAL 720 x 576 /50Hz
• SD: NTSC 720 x 480 /59.9Hz
• SD: NTSC 7.5 IRE (US standard)/ 0 IRE (Japan standard) options
• HDMI 1920 x 1080i/50
• HDMI 1920x1080i/60Hz
• HDMI 720 x 576 /50Hz
• HDMI 720x480i/60Hz
• Y:Cb:Cr, 4:2:2 10 bit

Preview Outputs

• 2x HDMI output
• Way 1:
HDMI 1 Multiscreen1: 9 smaller windows for inputs 1-9 with embedded audio level
indication (group1, channel 1)
HDMI 2 Multiscreen2: 3 smaller windows for inputs 10-12 with embedded audio level
indication (group1, channel 1) + 2 bigger windows for P Program,
embedded audio level indication for Program (group1, channel 1)
• Way 2:
HDMI 1 Multiscreen1- 12 smaller windows for inputs 1-12 with embedded audio
level indication (group1, channel 1) + 2 bigger windows for Preview and Program.
embedded audio level indication for Program (group1, channel 1)
HDMI 2 Multiscreen2 : Program, Multiscreen 1
• Way 3:
HDMI 1 Multiscreen1- 8 smaller windows for inputs 1-8 with embedded audio
level indication (group1, channel 1) + 2 bigger windows for Preview and Program.
embedded audio level indication for Program (group1, channel 1)
HDMI 2 Multiscreen 2 : Program, Multiscreen 1
• Resolution is 1920x1080i

Other Interface

• Serial D-Sub 9 Pin x 1 RS232
• Tally Output D-Sub 25 Pin x 12 Channel Open Collector Output
• Support Line and MIC mode
• GPI port

HD SDI signal

SMPTE 292M standard complied with

• Output return loss : More than 15 dB (5MHz to 750MHz)

More than 10 dB (750MHz to 1.5 GHz)

• Output level : 0.8 Vpp ± 10%
• Rise time : Less than 270 ps
• Fall time : Less than 270 ps
• Difference between rise time and fall time within 100 ps
• Alignment jitter : Less than 0.2 UI
• Timing jitter : Less than 1.0 UI
• Eye aperture ratio : More than 90%
• DC offset : 0 ± 0.5V
• Equalizer use 5C-FB cable support 100 meters

SD SDI signal

Analog Y/C, Composite CCIR601 NTSC and PAL

Operating Temperature

• 0°C to 40°C (32°F to 102°F)

Humidity

• 10% to 90% (non condensing)

Dimension & Weight

Base Unit : 482mm (W) x 88mm (H) x 302mm (D) = 9 Kg
Control Panel : 699.4mm (W) x 143.89mm (H) x 436.6mm (D) = 10 Kg

Power

• Input AC 100 ~ 240V Switching Adaptor, output DC 12V / 5A (48W)

«
...
42
43
44
45
»

Summary of Contents for SE-2800














































Reviews:

No comments

Related manuals for SE-2800

Brand: IBM Pages: 164

8265 Nways ATM Switch

Brand: IBM Pages: 174

Brand: Qlogic Pages: 135

SANbox2 SANbox2-64

Brand: Qlogic Pages: 224

dominion kx III

Brand: Raritan Pages: 6

Brand: Raritan Pages: 5

DOMINION KSX II

Brand: Raritan Pages: 7

Brand: Raritan Pages: 2

Brand: Ubiquiti Pages: 24

Brand: Ubiquiti Pages: 13

Brand: Ubisys Pages: 2

C4-SW120277 Series

Brand: Control 4 Pages: 4

Brand: CYP Pages: 32

Brand: Cabletron Systems Pages: 120

Brand: Key Digital Pages: 31

Brand: DLS Pages: 226

Brand: Gefen Pages: 14

Brand: GarrettCom Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands