background image

11 

one for longitude: 
 

 lon: 

DDºMM.FFFH 

  

  H:

 

E for eastern hemisphere, W for western hemisphere 

  

  DDD:

 0-180 degrees. 

  

  MM:

 0-59 

minutes 

  

  FFF:

 0-999 

1/1000 

minutes. 

 
 

example:

  

lon:   4º37.190E 

 
and one for the age of the position (HXV mode) or UTC time of last position (HVA mode): 
 

 

 

fix=DD 

mins 

old 

    (HXV 

mode) 

  

  DD:

 0-99 

minutes. 

 
 

 

fix=HH:MM 

UTC 

    (HVA 

mode) 

  

  HH:

 0-24 

hours. 

 

   

DD:

   0-59 minutes. 

 
 
The Buoy Finder 4A continuously searches for newer GPS positions in the incoming data. 
When a new GPS position is found, the position is updated.  
 
In HXV mode, the time elapsed (“age”) of the received buoy position is displayed in minutes. 
The age is referenced to the beginning of the transmission. It is not referenced to the time of 
acquisition. Please refer to the manual of the buoy for the time of acquisition relative to the start 
of a transmission. Normally, because a new position is sent every 30 minutes and receiving a 
position takes 4-6 minutes, the age of the position does not exceed 36 minutes.  
If the age of the last found position exceeds 60 minutes, the Buoy Finder 4A removes this 
position from its memory and will not show it anymore.  
 
In HVA mode, the UTC time of the last received position is given. The GPS position fix will be 
updated every 10 minutes.  
 

3.4.2 Heave 

The momentary heave that is received is also displayed between the messages of the GPS 
position and continuously when the receiver has not yet received a GPS position. 
 
The format is: 
 

 

heave: DDDD cm 

  

  DDDD:

 0-9999  cm. 

 

3.4.3 Bit errors 

When a vector (64 bit data part) is received with errors, the receiver shows the message: 
 

 bad 

vector 

 
 

Summary of Contents for 4A


























Reviews: