background image

2

CROSSLINE LASER LEVEL

TABLE OF CONTENT

SPECIFICATIONS  ........................................................................................................3
HAZARD SIGNAL WORD DEFINITIONS .................................................................3
GENERAL SAFETY RULES FOR OPERATION .........................................................4
COMPONENT IDENTIFICATION ...............................................................................5
OPERATION INSTRUCTION ......................................................................................6
CALIBRATION CHECK ................................................................................................7
MAINTENANCE AND SERVICE .................................................................................9
TROUBLESHOOTING .................................................................................................9
PRODUCT LABELS  .....................................................................................................10
WARRANTY INFORMATION .....................................................................................12

Summary of Contents for DT1H1V2PG













Reviews: