background image

9

OPERATING MANUAL

MAINTENANCE AND SERVICE

 

Do not attempt to open the device. To ensure product SAFETY and RELIABILITY, repairs, 

maintenance and adjustment should be performed by authorized service centres.  

Contact your dealer for more details. 

 

Do not drop, knock or shake the laser level as this will affect precision.

 

Remove batteries when the device is not in use. 

 

Keep the laser level clean at all times. Use a soft lint-free cloth for the body and lens tissue 

for glass windows. Do not use abrasive cleaners or solvents.

 

Don’t expose the laser level to high temperatures or humidity.

 

Do not store the laser level in hot areas, hot temperatures can short the life of electronic 

device, damage battery, and warp or melt certain plastics

 

Do not store the laser level in cold areas. When the unit warms up to its normal operating 

temperature, moisture can form inside where it may damage circuit board.

 

Avoid shock, vibrations and extreme heat.

 

Do not immerse the instrument in water.

 

Always slide the power switch to the OFF position when storing, transporting or moving 

around the job site.

 

Calibration service is recommended at least once a year or as needed. 

TROUBLESHOOTING

ISSUE

POSSIBLE CAUSE AND SOLUTIONS

Laser does not turn on

Check batteries. Make sure batteries are installed according to the 

correct polarity. 
The batteries may be depleted. Make sure the batteries are in proper 

working condition. If in doubt, try installing new batteries.
If the laser has been stored in extremely hot temperatures, allow it to 

cool.

Laser does not level

Instrument may be outside it’s levelling range. Position the 

instrument, tripod or the base surface.  
Instrument may have impact damage. Contact service centre for 

repair and calibration. 

Laser beam keeps flashing

Instrument may be outside it’s levelling range. Position the 

instrument, tripod or the base surface. 

Summary of Contents for DT1H1V2PR













Reviews: