background image

July 12, 2019 11:46 am

WARRANTY INFORMATION

This warranty is provided by DATUM of 20 Thackray Road, Port Melbourne VIC 3207. 

Phone: 1800 868 258.

Express Warranty

Subject to the exclusions set out below, we warrant that this product will be free from defects 

in materials or workmanship for 3 years (90 days for accessories, batteries and chargers) from 

the date of purchase.

The benefits conferred by this warranty are in addition to all rights and remedies which you 

may be entitled to under the Australian Consumer Law, and any other statutory rights you may 

have under other applicable laws. This warranty does not exclude, restrict or modify any such 

rights or remedies.

Warranty exclusions

This express warranty does not apply where a defect or other issue with the product is caused 

by normal wear and tear, misuse or abuse of the product. 

Consumer guarantees

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. 

You are entitled to a replacement or refund for a major failure and for compensation for any 

other reasonably foreseeable loss or damage.   

You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable 

quality and the failure does not amount to a major failure.

Warranty claims

To make a claim under this warranty, you must bring the product along with the proof of 

purchase and any other documentary evidence which you think is relevant to the your place of 

purchase where the claim will be handled on our behalf during the warranty period specified 

above. Any cost incurred by you in bringing the product to the place of purchase will be borne 

by you.

Calibration and repair service

Datum recommends to check instrument calibration at least once a year or on as needed 

basis. For calibration or repair service (not covered under warranty), please visit your place of 

purchase.

Summary of Contents for DTR30R

















Reviews: