4
!
Inadequate and/or unauthorised use of the treadmill is not allowed and we
warn you expressly against it.
All connection cables (power supply cable, data interface cable, etc) must be
securely installed and routed. You must make sure that no one could stumble
or fall down on them.
All the safety and usage instructions in this user manual must be most careful-
ly respected. In particular all the instruction about maintenance and technical
safety checks.
In the case of a detected, or even only suspected, fault or defect, the treadmill
must be put out of service for safety reasons, and clear visible sign must
be posted to that effect. This is to prevent it from being used inadvertently.
You should then contact the technical customer service department of daum
electronic gmbh.
Failure to comply with the safety prescriptions can cause in
juries or death.
Oil and other maintenance products, as well as parts of the device and of the
accessories, are not suitable for consumption. Therefore you should keep
them away from the reach of children and animals.
Warning! The manufacturer is not liable for personal physical injuries or ma-
terial damages.
When coupling many devices, care must be taken to avoid any danger ari-
sing from the summation of the leakage currents and to ensure the potential
equalisation is effected through a common current (power) supply (e.g. a wall
socket-outlet). If you have any questions please ask your dealer or the service
department of daum electronic gmbh.
If a socket with multiple outlets is installed after the initial start-up, no other
device may be connected to this socket. (use covers on the multiple sockets).
Only cables certified by daum electronic gmbh may be used to connect the
device with other devices.
A electrical shock hazard exists when touching devices that are not separately
grounded.
Defective or faulty devices and accessories may not be used.
The personal computer and all other connected devices (e.g. monitor, printer,
etc) must be installed at least 1.5m away from the training place, because lea-
kage currents could be generated on the housing (or use separate grounding,
housing leakage current).
The device is not suited for operation in rooms and / or areas with explosion
risks.
Cellular telephones may not be used in the direct vicinity of the device, they
may interfere with its functionality.
Electromagnetic interference are primarily characterised by the oscillation of
the displayed load value. If the displayed value varies often uncontrollably this
can be an effect of electromagnetic compatibility (EMC).
Treadmill ergometers are not suited for operation in rooms and / or areas with
explosion risks or in a combustive atmosphere. The devices may not be ope-
rated in the near vicinity of e.g. motors or transformers with big electrical con-
nections because electric or magnetic fields may disturb or deactivate some
functions. The vicinity of high voltage cables is also to be avoided.
Unless otherwise specified in the accompanying documentation and delivery
documents, all the devices are designed to be used in the usual closed condi-
tions under the climate conditions considered normal:
Tempe 10°... +40° C
The devices must therefore be protected against particular humidity effects.
Ventilation opening must not be covered in order to avoid restricting the circu-
lation of air. Storage temperature range: -20°C .....+50°C.
Technical specification
The ergo_run classic may not be used if the certifications/approval and the
defined safety standards do not comply with the local prescriptions. The local
country specifications must be compared with those of the device before using
the device and the device may only be used if they comply with each other.
Supplying power to the device:
The ergo_run classic must be connected to a 230Volt 50 Hz AC socket outlet.
This outlet must be protected by a 16 amperes fuse (C type).
Before connecting the device to the power outlet socket,
proceed with a careful visual examination of the power cord
and its plug to make sure they a free of damage. A damaged
cord and/or plug must immediately be replaced by an aut-
horised person.
Before connecting the ergo_run to the local power supply compare the spe-
cifications concerning voltage and frequency indicated on the nameplate with
your local power supply specifications. You may not connect the device be
-
fore doing this comparison.
The connection to the power supply socket must be done directly to the wall
socket. The usage of extension cords and/or multiplier socket is not allowed.
Power surges or power failure may cause the device to mal-
function and/or become defective, as well as to a complete
shutdown of the ergo_run. In order to restart the device in
this case you must switch the device OFF by means of the
mains switch and wait for the ON/OFF interval (about 1 - 2
minutes). Then you can restart the device.
Mains Voltage 230 Volt
Because of new regulations the mains voltage must be specified in the form
of a definite value. Consequently, the mains voltage values indicated with a
tolerance from 220 to 240 Volt will be restricted for all the ergometers of daum
electronic to the single mains voltage value of 230 Volt.
Mains Power Supply
In order to avoid all hazards any damages to the connection cable to the
mains power supply or to the On/Off switch must immediately be repaired, or
replaced with new parts, by the manufacturer, the customer service depart-
ment of the manufacturer, or similarly qualified service personnel.
Forbidden Use
Automatic operations (remote controlled from a computer) is forbidden, when
the health and the physical condition of the user do not allow this usage. Non
compliance to this can lead to injuries and serious health risks or even to
death.
Any utilisation with wheels (bicycle, wheelchair, inline skates or wheel skis),
as well as spiked running shoes or other spiked shoes on the standard run-
ning surfaces or belts is forbidden.
If you believe that not authorised persons may have access to the device,
or know of any other reason to lock the treadmill, then you must lock the
treadmill.
Used Symbols
The symbols used on the ergo_run premium8 comply with the IEC 417 and
IEC 878 standards (table D1/D2).
Warnings / Danger Notices
Accompanying documents / instructions.
Device of type B
Dangerous electrical voltage
!
!
!
Safety hints
