Dauphin PHONE CUBE Assembly Instructions Manual Download

Page: 2 / 16

https://www.kctoolco.com/hazet-863p-1-4-reversible-ratchet/

MINI REVERSIBLE RATCHET 1/4“ DRIVE

FOR

CORNER SCREWS ON TOP TRAVERSE BEAMS

ALTERNATIVE :

5MM ALLEN KEY

TOOLS REQUIRED:

HARDWARE INCLUDED:

BOTTOM FEET FILLERS

SCREWS

FOR DOOR

COVERS

FOR DOOR FRAME HOLES

ROOF CLIPS

TO SECURE CEILING

8MM HEX BOLT SCREWS

TO SECURE

PANELS TO TOP TRAVERSE

DESK KIT THREADED INSERTS

AND LOCK NUTS

TO SECURE DESK TO PANEL

RUBBER MALLET

FOR INSERTING PANELS

1/8” DRILL BIT

FOR DOOR

CORNER SQUARE

TO ALIGN FRAME

FLAT PALLET KNIFE

TO FACILITATE PANEL INSTALL

SPIRIT/LASER LEVEL

TO LEVEL THE UNIT

CLAMPS

TO FACILITATE PANEL INSTALL AND PLACING POST

#13 / 13MM FLAT WRENCH

FOR LEVELING THE GLIDES OF

8MM HEX BIT WITH EXTENSION

FOR HEX BOLT SCREWS

6MM ALLEN KEY

FOR ROOF CLIPS

PHILLIPS HEAD BIT

FOR SCREWS FOR DOOR FRAME

TWO 9 FT. STEP LADDERS

FOR INSTALLING ROOF & PANELS

MOVING CART/DOLLY

FOR TRANSPORTING

PANELS, ROOF, AND POSTS

Req. Length for post-post: 48”

Summary of Contents for PHONE CUBE

















Search results

Summary of Contents for PHONE CUBE

Reviews:

Related manuals for PHONE CUBE

Brands by name

Popular brands

Dauphin PHONE CUBE, Assembly Instructions Manual

Search results

Summary of Contents for PHONE CUBE

Reviews:

Related manuals for PHONE CUBE

Brands by name

Popular brands