background image

3

INTRODUCTION

congratulations on your purchase of a high quality, award winning 
aquashield maX ultra Violet water treatment system.
aquashield maX represents advances in safety and convenience of 
rainwater harvesting technology for commercial and large scale rainwater 
users. the range offers increased water treatment quality and safety 
- producing water that is biologically safe to drink, without the use of 
chemicals.
This all in one unit is pre fitted with a correctly matched pump, Filterpure

®

 

and Steriflo

®

 units and can come with either the rainbank

®

 mk11 or the 

torrium

®

 pump controller.

the huge advantage of the aquashield maX pre engineered pack is that 
davey do all the work and all thinking for you.  advantages like the pump 
interlocking and lamp count down timer ensures only correctly disinfected 
water is delivered.

Applications: Pressure boosting and disinfection of rainwater for:

•  School shower and toilet blocks 
•  Commercial toilet flushing
•  Large home potable water supply
•  Industry process water treatment 
•  Guest house potable water supply
•  Bacteria and algae growth control for aquaculture and water features
•  Also suitable for bore and surface water treatment – *subject to a water 

quality test

Features & Benefits:

•  Factory matched and tested package – ensures correct UV dosage and 

high reliability

•  Pump interlock  detects lamp failure and locks pump out– ensures only 

disinfected water is delivered

•  Lamp count down timer with set limit of 9000 hours - ensures only 

disinfected water is delivered

•  Durable UV resistant cover – allows for flexible, vandal resistant exterior 

installation 

•  RainBank

®

  mK II controller options – provides seamless automatic 

mains water backup 

•  Torrium

®

 controller options – intelligent automatic pump control 

maximizes pump efficiency by adjusting run on time and cut in pressures

•  2 x 20” Jumbo cartridge filter housings – for low friction losses and long 

cleaning intervals

•   20 micron filtration – for long cleaning intervals and dirt, rust, sediment 

and debris reduction

•  1 micron filtration – for parasitic cyst reduction and high UV dosage rates

Summary of Contents for aquashield MAX

























Reviews: