9
support bracket of the hood with two 5x45 mm screws.
4.
Hang the hood onto the lower bracket.
5.
Adjust the distance of the hood from the wall.
6.
Adjust the horizontal position of the hood.
7.
Using a pencil mark the cooker hood permanent drill hole
inside the suction group.
8.
Remove the hood from the lower bracket.
9.
Drill at the point marked (Ø8mm).
10.
Insert 1 wall screw anchor.
11.
Apply the flues support bracket
G
to the wall adherent to
the ceiling, use the flues support bracket as a perforation
diagram (if present, the small slot on the support must
coincide with the line drawn previously on the wall) and
mark two holes with a pencil. Make the holes (Ø8mm),
and insert 2 dowels.
12.
Fix the chimney support bracket to the wall using two
5x45mm screws.
13.
Hook the hood onto the bottom bracket.
14.
Fix the hood into its final position on the wall
(ABSOLUTELY ESSENTIAL).
15.
Connect a pipe (pipe and pipe clamps not provided, to be
purchased separately) for discharge of fumes to the
connection ring located over the suction motor unit.
If the hood is to be used in ducting version, the other end
of the pipe must be connected to a device expelling the
fumes to the outside. If the hood is to be used in filter
version, then fix the deflector
F
to the chimney support
bracket
G
and connect the other extremity of the pipe to
the connection ring placed on the deflector
F
.
16.
Connect the electricity.
17.
Apply the chimney stacks and fasten them at the top to
the chimney support
G
(17b) using 2 screws (17a)
18.
Slide the bottom section of the chimney down until it
completely covers the suction unit and slots into the
housing provided on top of the hood.
Remount the carbon filter frame and the fat/s filter/s and check
the perfect functioning of the hood.
Also install the supplied perimeter suction panels
Description of the hood
Fig. 1
1.
Control panel
2.
Grease filter
3.
Grease filter release handle
4.
Halogen lamp
5.
Vapour screen
6.
Telescopic chimney
7.
Air outlet (used for filter version only)
8.
Perimeter suction panel
Operation
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Functioning – Model with Keyboard
A
B
C
D
A.
on/off light switch
B.
on/off aspiration switch and minimum power selection
B+C.
medium power selection aspiration switch
B+D.
maximum power selection aspiration switch
Maintenance
Prior to any maintenance operation ensure that the cooker
hood is disconnected from the power supply.
Cleaning
The cooker hood should be cleaned regularly (at least with the
same frequency with which you carry out maintenance of the
fat filters) internally and externally. Clean using the cloth
dampened with neutral liquid detergent. Do not use abrasive
products.
DO NOT USE ALCOHOL!
Warning:
Failure to carry out the basic standards of the
cleaning of the cooker hood and replacement of the filters may
cause fire risks.
Therefore we recommend observing these instructions.
Maintenance of the perimeter suction panel
Dismantling:
pull the panel out decisively and remove it from all the
connecting points.
Cleaning:
the suction panel should be cleaned with the same
frequency as the fat filters, using a cloth soaked in
neutral liquid detergents.
Avoid the use of products containing abrasives. DO NOT
USE ALCOHOL!
Montage:
The panel should be fixed between the pins placed for
this reason on the surface of the hood.
Attention!
Always check that the panel is fixed in its
place well.
Grease filter
Fig. 2
This must be cleaned once a month (or when the filter
saturation indication system – if envisaged on the model in
possession – indicates this necessity) using non aggressive
detergents, either by hand or in the dishwasher, which must
be set to a low temperature and a short cycle. When washed
in a dishwasher, the grease filter may discolour slightly, but
this does not affect its filtering capacity.
To remove the grease filter
B
, pull the spring release handle.
