8
Manual
DV‑12
1 =
Continue ‘ON’
0 = Everything ‘OFF’
= The DV-12 switches at the set times.
• Put the 3-position switch on the clock
.
• Now we have to determine when the DV-12
needs to be switched ‘ON’ and ‘OFF’.
• Therefore, the pins (the so called ‘running
weights’) that are around the clock need to be
pushed out.
Are the pins pushed INWARDS; The clock will
switch ‘OFF’.
Are the pins pushed OUTWARDS; The clock
will switch ‘ON’.
• To have the timer switch between 2 times (the
‘ON’ time, and the ‘OFF’ time), ALL the pins
between those 2 times need to be pushed out.
• The shortest switch position of the clock is
15 minutes.
• When you have determined the ‘ON’ and
‘OFF’ times, turn the clock slowly (manually)
clockwise to make sure everything is correct.
• If you are sure that everything switches at the
right time, the DV-12 is ready for use.
1.6 FOR YOUR SAFETY
• The correct operation of the DV-12 is only
guaranteed, if you observe this manual.
• Although it is possible to install the DV-12
yourself, we recommend to have this done by
a certified installer.
• Before installing the DV-12, the 220V voltage
MUST be taken off the power point (Check
this!)
• This guide should only be used for the DV-12.
• DAVIN
®
products are covered by a 1-year
warranty.
• To qualify for this warranty, you are required
to return the DV-12 to the point of sale.
• If changes are made to DAVIN
®
products
without the express and written prior
permission of the manufacturer, the warranty
will become void.
• The DAVIN
®
warranty will also become void
with improper installation of the DV-12.
• Neither the manufacturer, nor the importer,
nor the retailers of the DV-12 are liable for
damages arising from the use of the DV-12.
SERVICE NUMBER / HELPDESK:
+31 (0)6 – 14 813 447
1.0 INFORMACIÓN GENERAL
El DV-12 es un caja de relés con temporizador
que controla un máximo de 2 accesorios de
600W o 2 de 400W.
1.1 DATOS TÉCHNICOS
Dimensiones
: 110 x 210 x 70mm.
Corriente requerida
: 230 Vac / 50Hz.
Potencia máxima
: 6 amperios.
Grado de protección
: IP-44
1.2 CORRIENTE REQUERIDA PARA EL DV-12
Para conectar el DV-12 debe utilizar un
grupo eléctrico de por lo menos 6 amperios,
preferiblemente un grupo exclusivo. Un grupo
exclusivo es un grupo eléctrico que se puede
usar exclusivamente para el
DV-12. Si no dispone de un grupo exclusivo, le
recomendamos que encargue su instalación a
un instalador autorizado
El DV-12 dispone de un fusible térmico de
6 amperios, que apaga automáticamente el
DV-12 en caso de sobrecarga o cortocircuito.
(Ver también punto 1.6.)
1.3 INSTALACIÓN DEL DV-12
En la parte trasera del DV-12 encontrará dos
soportes de montaje con los que instalar el
DV-12 sobre una superficie lisa.
¡ATENCIÓN!
El reloj analógico es una parte delicada del
DV-12 sensible a golpes fuertes.
• Monte el DV-12 cerca de su grupo exclusivo.
• En la parte inferior del DV-12 encontrará un
cable con toma de tierra (230V).
Manual del
DV‑12
DV-12 Binnenwerk PMS.indd 6
30-10-2012 14:08:21
