Davis Instruments Health EnviroMonitor, User Manual

H

EALTH

 E

NVIRO

M

ONITOR

 S

YSTEM

 C

ONSOLE

 Q

UICK

 R

EFERENCE

F

UNCTION

 K

EYS

The lists below indicate what condition appears 
when you press each function key. Each time you 
press the key, the next item in the list appears.

ET (Evapotranspiration)

Daily ETo Sum
Total ETo for the Period
Average Daily ETo for the Period
Period Start Date
ETo AutoClear Status

DEG DAYS (Growing Degree-Days)

Daily Degree-Day Sum
Total Degree-Days for the Period
Average Daily Degree-Days for the Period
Base Degree-Day Threshold
Upper Degree-Day Threshold
Period Start Date
Degree-Day Auto Clear Status

TEMP (Temperature)

Current Air Temperature
Current Soil Temperature
Current Temperature-Humidity Index
Current Wind Chill
Temperature AutoClear Status

WIND (Wind)

Current Wind Speed
Daily Wind Run
Average Daily Wind Run for the Period
Current Wind Direction
Period Start Date
Wind AutoClear Status

SUN (Solar Radiation)

Current Solar Radiation Intensity
Daily Incident Solar Energy Sum
Average Daily Solar Energy for the Period
Period Start Date
Daily Solar Energy AutoClear Status

RAIN (Rainfall)

Daily Rainfall and Rate of Rainfall
Total Rainfall
Rainfall AutoClear Status

BAR (Barometric Pressure)

Current Barometric Pressure

HUM (Relative Humidity)

Current Relative Humidity
Relative Humidity AutoClear Status

DEW (Dew Point/Leaf Wetness)

Current Dew Point
Current Leaf Wetness

TIME (Time and Date)

Current Time
Current Date
Current Year
AutoClear Time
Period Start Date

H

IGHS

AND

 L

OWS

See “Highs and Lows” on page 13 for a list of highs 
and lows stored by the console.

• To view the high or low, press the appropriate 

function key to display the desired condition. 
Press 

Recall

 to view the high/low. Wait a few 

seconds and the time at which the high/low 
occurred will appear. Press 

Recall

 again to 

view the low if both a high and low are stored.

• To clear a high/low, press the appropriate 

keys as necessary to display the desired high/
low. Press and hold 

Clear

 until the high/low 

value is cleared.

A

LARMS

See “Alarms” on page 14 for a list of available 
alarms.

• To view an alarm threshold, press the appro-

priate function key to display the desired con-
dition. Press 

Alarm

 to view the threshold.

• To set an alarm, press the appropriate keys to 

display the desired alarm threshold. Use 

Enter

to set the threshold.

• To silence an alarm, press 

Clear

.

• To clear an alarm, press the appropriate keys 

to display the desired alarm threshold. Press 
and hold 

Clear

 until the alarm threshold is 

cleared.

P

ERIOD

 I

NFORMATION

The console uses a single time period for all values 
which accumulate totals or calculate averages over 
an interval. See “Period” on page 12 for a list of val-
ues accumulated or averages calculated during the 
period.

• To clear all ”period” information and start a 

new period, press 

TIME

 as necessary to dis-

play the period start date. Press and hold 

Clear

 until the period information is cleared.

A

UTO

C

LEAR

The console may be set to automatically clear some 
or all daily values at the same time each day. See 
“AutoClear” on page 13 for a list of all information 
which may be cleared using AutoClear.

• To enable/disable AutoClear for a condition 

or group of conditions, press the appropriate 
function key as necessary to display the Auto-
Clear status. Press 

Enter

 to toggle the Auto-

Clear setting between OFF and ON.

• To set the time at which AutoClear clears val-

ues, press 

TIME

 as necessary to display the 

AutoClear time. Use 

Enter

 to set the desired 

time.

C

HOOSING

 U

NITS

OF

 M

EASURE

To select the unit of measure in which a condition is 
displayed, press the appropriate function key to 
display the desired condition. Press 

UNITS

 until 

the desired unit of measure appears in the display.