background image

 

This equipment has been tested and found to comply with the limits for a Class B digital de-

vice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turn-

ing the equipment on and off, the user is encouraged to try to correct the interference by one

or more of the following measures: 

•Reorient or relocate the receiving antenna

•Increase the separation between the equipment and receiver

•Connect the equipment into an outlet on a circuit different from that to which the re-

ceiver is connected

•Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved in writing by Davis Instruments may void

the user’s authority to operate this equipment.

 

Product Number: 6510C

Davis Instruments Part Number: 7395.160
WeatherLink

 

®

 

 for Vantage Pro

Rev. A Getting Started Guide (April 25, 2001)

© Davis Instruments Corp. 2001. All rights reserved.

This product complies with the essential protection requirements of the EC 
EMC Directive 89/336/EC

Vantage Pro, Weather Monitor II, Weather Wizard III, and WeatherLink are 
trademarks of Davis Instruments Corp. Hayes is a registered trademark of 
Hayes Microcomputer Products, Inc. Windows is a trademark of Microsoft Cor-
poration. 

Summary of Contents for and Vantage Pro

















Reviews: