background image

9

3.  Wipe the spa shell clean with a damp cloth. Remove

the two warning decals (not shown) from the spa
shell. 

Before filling the spa, make sure it is in the

exact position you want. Also make sure the spa
can be easily serviced, if needed. Once the spa
is filled with water, it must be drained to be
moved.

Fill the spa by using a garden hose or other clean
water source. 

Do not use soft water.

The water

temperature does not matter; however, if you use
warm or hot water, the spa will be ready to use
sooner. Fill the spa until the water covers the filter
assembly by approximately one inch. 

Do not overfill

the spa.

4. Attach the nozzle of an air pump (not included) to

the valve on the Inflatable Cover (4) and fill the
Inflatable Cover with air.

Do not overfill the

Inflatable Cover.

Slide one of the straps on the inside of the Spa
Cover (11) through one of the loops on the Inflatable
Cover (4). Attach the latch on the strap to the buckle
on the other end. 

Make sure the cut-out on the

Inflatable Cover is lined up with the warning
label on the Spa Cover. 

Attach the other three

straps on the inside of the Spa Cover (11) through
the loops on the Inflatable Cover (4) in the same
manner. Place the Spa Cover (11) over the spa and
line up the cut-out in the Inflatable Cover with the
Console.

5.

See the inset drawing.

Position one of the Buckles

(30) on the wood panels on the spa unit. Hold the
Buckle in place so the strap on the Spa Cover (11) is
tight. (Note: It may be easier to position the Buckle if
a second person holds the strap on the opposite
side of the Spa Cover tight.) 

The Spa Cover must

be tight. Do not place the Buckle over one of the
grooves in the wood panels.

Remove the latch.

Attach the Buckle to the side of the spa with two #4
x 3/4Ó Screws (31). 

Note: It may be helpful to use

a drill with a 1/16Ó drill bit to make starter holes
in the wood panels. You may also want to apply
a little soap or wax to the screw threads.

Attach the other five Buckles (30) to the spa unit in
the same manner.

Remove the Spa Cover (11) and Inflatable Cover (4)
from the spa unit.

3

4

Fill to Here

Loop

Buckle

Strap

Warning

Label

Cut-out

Latch

4

11

5

Strap

Latch

30

31

11

30

Summary of Contents for Daybreak 860 WLHS86090





















Reviews: