background image

If  equipment  failure  occurs  in  the  normal  course  of  service  having  been 
competently  installed  and when operating within its specified duty limits warranty 
will be provided as follows:-

Ÿ

 

Up to two years - The item will be replaced or repaired at no charge.

Ÿ

 Over two years, less than three years - The item will be replaced or 
repaired at a cost to the customer of 50% of the Davis & Shirtliff 
market price.

The warranty on equipment supplied or installed by others is conditional upon the 
defective unit 

being promptly returned free to a Davis & Shirtliff ofce

 and 

collected thereafter when repaired. No element of site repair is included in the 
warranty  and  any  site  attendance  costs  will  be  payable  in  full  at  standard 
charegeout rates. Also proof of purchase including the purchase invoice must be 
provided for a warranty claim to be considered.

Ÿ

In lieu of any warranty, condition or liability implied by law, the liability of  Davis 
& Shirtliff (hereafter called the Company) in respect of any defect or failure of 
equipment supplied

 is limited to making good by replacement or repair 

(at the Company’s discretion) defects which under proper use appear therein 
and  arise  solely  from  faulty  design,  materials  or  workmanship  within  a 
specified period. This period commences 

immediately after the equipment 

has been delivered to the customer

 and at its termination all liability ceases. 

Also the warranty period will be assessed 

on the basis of the date that the 

Company is informed of the failure

.

Ÿ

The warranty applies solely to equipment supplied and no claim for 
consequential  damages

,  however  arising,  will  be  entertained.  Also  the 

warranty specifically excluded defects caused by fair wear and tear, the effects 
of careless handling, lack of maintenance, faulty installation, incompetence 
on part of the equipment user, Acts of God or any other cause beyond the 
Company’s reasonable control. Also, any repair or attempt at repair carried 
out by any other party 

invalidates all warranties.

7.  TERMS OF WARRANTY

i)  General Liability 

ii)   Standard Warranty

       

111

Summary of Contents for DQA

















Reviews: