background image

Chapter 3 – Troubleshooting Guide

Genesis MP

22

Flowcharts

All procedures should be used as flowcharts to help with the diag-
nosis of defective modules. Please use the index to start isolating
possible symptoms. If step 1 doesn’t correct the problem, go to the
next step and so forth. Once the defective component has been
isolated, please refer to the Removal and Replacement section to
remove it.

Once you have removed the defective component, refer to
Chapter 2 - Service Policies to obtain replacement parts from
DayStar.

Index of Troubleshooting Flowcharts

The CUDA Chip

Power Supply

Error Chords

The System

Display

Floppy Drive

Hard Drive

Peripherals

CD-ROM

The CUDA Chip

The definition for the CUDA Chip is as follows:

A microcontroller chip that serves as the managing circuitry for the
Apple Desktop Bus and the real-time clock. It oversees the power
on and off of the system. It maintains the parameter RAM, better
known as PRAM. It also manages and maintains information
regarding all system resets from various commands. Examples of
this are: keyboard restart, loss of power, software restart.

Location of the CUDA Chip
and reset switch

Summary of Contents for Genesis MP

















































































Reviews: