DAYTEK M32 Product Manual Download

Page: 10 / 12

HOW TO RESTRING/REPLACE THE LINE ON YOUR DAYTEK ROTARY CLOTHESLINE

ARM 3

ARM 2

ARM 1 – LINE END

ARM 4

A. Tensioner Block Bottom

–

recessed into the arm of the
clothesline.

B. Tensioner Block Top

–

positioned on top of the
bottom block.

TO REPLACE A LINE ON YOUR DAYTEK ROTARY
CLOTHESLINE, YOU MUST REMOVE THE TENSIONER
BLOCK TOPS OFF THE AFFECTED LINE.

C. Bolt

– head of bolt under

the arm of the clothesline.

D. Nut

– seated in the top of

the line tensioner.

To remove the Tensioner Block Tops

Remove the line from the Tensioner Block.

Work your way around the clothesline
removing all four Terminal Blocks Tops
and the line.

Place your index finger on top of the Tensioner
Block and over the Nut to ensure that the Nut is
held in position.

Undo and loosen the bolt from under the arm of
the clothesline.

Once the bolt is fully loose, you can

carefully remove the Tensioner Block Top & Nut.

Summary of Contents for M32













Search results

Summary of Contents for M32

Reviews:

Related manuals for M32

Brands by name

Popular brands

DAYTEK M32, Product Manual

Search results

Summary of Contents for M32

Reviews:

Related manuals for M32

Brands by name

Popular brands