DAYTEK M32 Product Manual Download

Page: 11 / 12

HOW TO TENSION THE LINE ON YOUR DAYTEK ROTARY CLOTHESLINE

To attach a new line

1. Start by clamping one end of the new line into

ARM 1

as shown below (ARM 1 can be any arm

you choose).

2. Work your way around the clothesline

attaching the line at

ARM 2, 3 & 4

as shown

below. Ensure line is pulled tight and clamped
in Tensioner Block before moving on to
next arm.

3. When you arrive back at

ARM 1

, remove the

Tensioner Block Top and clamp both line ends
into line tensioner as shown below, making
sure the lines are pulled tight.

4. Trim line ends leaving approximately 5cm.

1. At the required tensioning point, place your index

finger on top of the Tensioner Block Top and over
the Nut to ensure that the Nut is held in position.

2. Loosen the bolt from under the arm of the

clothesline.

3. Pull the line through the Tensioner Block to

required tension and re-tighten the bolt.

4. Repeat this process around the clothesline

working the slack cord towards the end of
the line.

ARM 1

STRING BOTH ENDS

TERMINAL BLOCK TOP AFFIXED

STRING ONE END

ARM 2, 3 & 4

TERMINAL BLOCK TOP AFFIXED

STRING LINE

Summary of Contents for M32













Search results

Summary of Contents for M32

Reviews:

Related manuals for M32

Brands by name

Popular brands

DAYTEK M32, Product Manual

Search results

Summary of Contents for M32

Reviews:

Related manuals for M32

Brands by name

Popular brands