background image

9

ADJUSTING THE HEIGHT OF YOUR ROTARY CLOTHESLINE

HELPFUL HINTS

IMPORTANT

The ideal height of the clothesline should be 
approximately 50mm from the users head to 
the underside of the horizontal arms.
To adjust the clothesline to higher position 
simply remove the support ring from the 
ground socket, lift the clothesline and rotate 
to either slot 1, 2 or 3. Each position will 
increase your clothesline height by 75mm. 
With the slothesline at the required height 
replace the support ring into the ground 
socket to secure the clothesline.

•  Engage the wind brake mechanism while hanging laundry. By pulling sideways on  

the horizontal arms the clothesline will rotate to the next loading position.

•  Hang washing starting from the inside line with small garments.

•  Distribute the weight of the washing evenly on each line around the four quadrants

•  After hanging the washing it is important to wind the line up off the wind brake for spin air drying.

• Located at the end of each horizontal arm is a clothes hanger loop.

Please ensure your clothesline is not used as a playing item by children swinging 
on lines and main arms. Any damage from misuse will void the warranty.

1

3

2

HIGHEST

MEDIUM

LOWEST

1

2

2

1

3

3

Summary of Contents for M32













Reviews: