background image

                                                                           

 

 

7

 

 

ALU3 

1.    Turn on machine 

2.

 

Input a,b,d value 

3.

 

Press ALU button, indicator lit up 

4.

 

Start spin, after spin stop 

Clip on weight on 

inside rim edge, add 

adhesive weight on 

outside rim shoulder 

 

ALU1 

1.    Turn on machine 

2

 

Input a,b,d value 

3

 

Press ALU button, indicator lit up 

4

Start spin, after spin stop 

Add adhesive weights 

on the rim shoulder 

both sides 

 

ALUS 

1.    Turn on machine 
2.    Press ALU button, indicator lit up 
3.    Input aI,aE,d value   
4.    Start spin, after spin stop 

Add adhesive weights 

on the two positions 

gauge head touch 

 

Static mode, for 

motorcycle 

wheels

 

1.

 

Turn on machine

 

2.

 

Input a,b,d value

 

3.

 

Press ALU button

 

Start spin, after spin stop

 

Add adhesive weight

 

 

 

 
Key board (H) 

Icon 

Function 

Icon 

Function 

 

Set distance   

 

Optimization of unbalance 

 

Set rim width 

  

 

Selection of “ALU” modes   

 

Set rim diameter 

 

Static mode, for motorcycle wheels 

“ST” Will show in right display 

 

Recalculation 

 

Unbalance display pitch and threshold 

 

Start 

 

Stop/Cancel 

 

 

Summary of Contents for B917




















Reviews:

Related manuals for B917