3.
Locate the POWER SELECTOR BOARD under the fuse. Note the number
visible on this board, indicating the present nominal voltage setting (120 or
220).
4.
With one finger, slightly raise up the level labelled “FUSE PULL,” and then,
with a needle-nosed pliers held in the other hand, pull out the POWER
SELECTOR BOARD.
5.
Turn over the board and reinsert it so that the value of the desired nominal
voltage is visible (“100” and “240,” if present, are NOT to be used).
If you change the voltage-level setting, YOU MUST ALSO
CHANGE THE
MAINFRAME’S BUSS FUSE
BEFORE POWERING UP THE MAINFRAME, as
follows:
Power
Required
Level
Fuse
120 V-AC
4 A
220 V-AC
2 A
For instructions, see “Changing the Fuse,” below.
C
HECK
EEPROM S
WITCH
When mainframe power is turned ON or OFF, the EEPROM Write Protect Switch
should be
OFF
(in the downward position).
C
ONNECT
P
OWER
C
ORD
Plug the six-foot power cord supplied with your mainframe into the AC power
connector on the rear of the unit. Plug the other end into your primary power
source. The offset pin on the power connector is ground; to safely operate the
mainframe from a two-contact outlet, use a 3-prong-to-2-prong adaptor and con-
nect the green pigtail on the adaptor to earth ground.
NOTE:
Since the presence of electrical noise can affect the ultimate integrity of
your data, the noise level should be suppressed as much as possible. In particu-
lar, care should be taken to avoid utility-line problems that can interfere with or
possibly even damage sensitive microprocessor-based equipment. Such noise
can also be generated by electrical motors, relays, and motor control devices.
While your System 10 mainframe has internal circuitry to protect it from overvolt-
age transients and mild EMI, a clean line is still very desirable. No protection is
provided against a dropout longer than 8 milliseconds or brownout below 95
volts. Depending on your line conditions, a number of protective devices are
available (isolators, regulators, uninterruptible power supplies, etc.). Contact the
Daytronic factory for more information.
T
URN
ON
THE
M
AINFRAME
Refer to the respective diagram in the “Physical Layout” section of the appropri-
ate “On the Air” book for the location of your mainframe’s POWER ON/OFF switch
or button.*
1-4
1.A
G
ETTING
S
TARTED
1.A.3 M
AINFRAME
P
OWERUP
* Note that the
Model 10KN8A
(only) has a combined POWER ON-OFF and CIRCUIT BREAKER
button.
Summary of Contents for System 10
