www.dbtechnologies.com
info@dbtechnologies-aeb.com
INGENIA IG3T
Rev 1.1 cod. 420120239Q
Technical Data
Speaker Type
:
2-way Active Speaker
Acoustical data
Frequency Response [-10dB]
:
53 - 20.000 Hz
Frequency Response [-6dB]
:
57 – 19.200 Hz
Max SPL
:
132 dB
HF compression driver
:
1.4" Exit
HF voice coil
:
3” Titanium
Horn Coverage (HxV)
:
110 x 90° (+20°/-70°)
Directivity
:
Vertical asymmetric
HF type
:
Neodymium compression driver
Crossover frequency
:
1100 Hz
LF
:
2x10”
LF Voice Coil
:
2.5”
LF Type
:
Neodymium
Amplifier
Amp Technology
:
Digipro® G3
Amp Class
:
Class-D
RMS Power
:
900 W
Peak Power:
1800 W
Processor
Controller
:
DSP 56 bit
AD/DA Converter
:
24 bit / 48 kHz
Limiter
:
Dual Active, Peak, RMS, Thermal
Input
Signal Input
:
1x Combo IN (XLR/Jack)
Signal Out
:
1 XLR link OUT
USB connector
:
Yes – mini USB
Mechanics
Housing:
Polypropylene PP reinforced by internal metal
structure
Grille
:
FULL / Invisible screws
Flyable:
Yes
Handles
:
1x on TOP / 1x on BOTTOM
Pole Mount
:
Yes, 36 mm
Width
:
280 mm (11.02 in)
Height
:
806 mm (31.73 in)
Depth
:
393 mm (15.47 in)
Weight
:
20.8 kg – 45.86 lbs.
User Interface
:
OLED d push rotary encoder
Self-rotating display
:
yes
Positioning
:
EPD (Element Position Detection)
Display mirroring
:
Yes
Download the complete user manual on:
www.dbtechnologies.com/EN/Downloads.aspx
EMI CLASSIFICATION
According to the standards EN 55103 this equipment is designed and suitable to operate in E3 (or lower E2, E1) Electromagnetic environments.
FCC CLASS B STATEMENT ACCORDING TO TITLE 47, PART 15, SUBPART B, §15.105
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
WARNING:
Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties.
For safety reasons do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check
all the components for damages, deformations, missing or damaged parts that may compromise safety during installation. If you use the
loudspeakers outdoor avoid spots exposed to bad weather conditions.
Contact dB Technologies for accessories to be used with speakers. dBTechnologies will not accept any responsibility for damages caused by
inappropriate accessories or additional devices.
Features, specification and appearance of products are subject to change without notice.
dBTechnologies reserves the right to make changes or improvements in design or manufacturing without assuming any obligation to change
or improve products previously manufactured.
Scan with your QR Reader
App to download the
complete User Manual
