www.dbtechnologies.com
info@dbtechnologies
‐
aeb.com
VIO
S218
420120267Q
REV.1.1
Technical Data
Speaker Type
:
Active bass-reflex subwoofer
Acoustical data
Frequency Response [-6 dB]
:
28 Hz – Cut frequency
(crossover - dependent)
Frequency Response [-10 dB (HPF)]
:
27 Hz
Max SPL (1 m)
:
143 dB
LF
:
2 x 18”, Neodymium
LF Voice Coil
:
4”
Crossover freq.
:
60 to 110 Hz + full-range
Directivity:
(omnidirectional) Cardioid with DSP
Amplifier
Amp Technology
:
Digipro® G4
Power supply
:
Full range with PFC
Amp Class
:
Class-D
RMS Power
:
3200 W
Peak Power:
6400 W
Cooling:
Passive (convection) and internal fan
Operating voltage:
100-240V~ 50-60 Hz (Full Range)
Processor
Controller
:
DSP, 32 bit
AD/DA Converter:
24 bit / 96 kHz
Limiter
:
Peak, RMS, Thermal
Controls
:
Rotary Delay Control (0-9.9 ms, steps: 0.1 ms),
switches (Link/Xover, Cardioid Preset, System test,
Polarity), Subwoofer Attenuation, Xover LPF
Input/Output
Mains connections
:
PowerCON
®
TRUE1 In/link
Maximum number of subwoofer for each daisy chain
power connection [mains input + mains link]:
1+1 VIO
S218** (220-240V~), 1+0 VIO S218** (100-120V~)
Signal Input
:
(
Balanced)
1x IN (female)
Signal Out
: (
Balanced) Link OUT (male) + HPF Xover
RDNET connectors:
Data
In
/
Data
Out
USB connector
:
standard USB B-type (for SERVICE DATA)
Mechanics
Housing:
Wooden box/black polyurea finish
Grille
:
Full metal (CNC machining)
Handles
:
4 per side
Pick points (stack mode):
yes on top
Roping points:
4
Width
:
1300 mm (51.18 in)
Height
:
520 mm (20.47 in)
Depth
:
800 mm (31.50 in)
Weight
:
85.6 kg (188.72 lbs.)
Download the complete user manual on:
www.dbtechnologies.com/EN/Downloads.aspx
EMI CLASSIFICATION
According to the standards EN 55103 this equipment is designed and suitable to operate in E5 Electromagnetic environments.
FCC CLASS A STATEMENT ACCORDING TO TITLE 47, PART 15, SUBPART B, §15.105
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
WARNING:
This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.
WARNING:
Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties.
For safety reasons do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check
all the components for damages, deformations, missing or damaged parts that may compromise safety during installation. If you use the
loudspeakers outdoor avoid spots exposed to bad weather conditions.
Contact dB Technologies for accessories to be used with speakers. dBTechnologies will not accept any responsibility for damages caused by
inappropriate accessories or additional devices.
Features, specification and appearance of products are subject to change without notice.
dBTechnologies reserves the right to make changes or improvements in design or manufacturing without assuming any obligation to change
or improve products previously manufactured.
Scan with
your QR
Reader App to
download the
complete User
Manual
