background image

586

Verify that the 586’s package contains the following:

• 586 Unit (according to Model number marked on package)
• AC Power Cord
• Operation Manual
• Registration Card
• Rack screws

If any of these items are missing, contact dbx customer service at (801) 568-7660.

This warranty is valid only for the original purchaser and only in the United States. We warrant dbx prod-
ucts against defects in materials or workmanship for a period of two years from the date of original pur-
chase for use, and agree to repair or, at our option, replace any defective item, except external power trans-
formers, without charge for either parts or labor.

IMPORTANT:This warranty does not cover damage resulting from accident, misuse or abuse, lack of rea-
sonable care, the affixing of an attachment not provided with the product, loss of parts, or connecting the
product to any but the specified receptacles.This warranty is void unless service or repairs are performed
by an authorized service center. No responsibility is assumed for any special, incidental or consequential
damages. However, the limitation of any right or remedy shall not be effective where such is prohibited or
restricted by law.

Simply take or ship your dbx product prepaid to our service department. Be sure to include your sales slip
as proof of purchase date. (We will not repair transit damage under the no-charge terms of this warranty.)
dbx will pay return shipping.

NOTE: No other warranty, written or oral is authorized for dbx products.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state. Some states do not allow the exclusion of limitations of incidental or consequential damages or lim-
itations on how long an implied warranty lasts, so the above exclusion and limitations may not apply to
you.

Wa

arra

antty

y

Ins

sp

pec

cttio

on

3

Summary of Contents for 586

















Reviews: