INSTALLATION INSTRUCTIONS • ALX CONTEMPORARY CABLE RAILING
ALX CONTEMPORARY CABLE INSTALLATION INSTRUCTIONS 29
THE DIAGRAMS AND INSTRUCTIONS IN THIS BROCHURE ARE FOR ILLUSTRATION PURPOSES ONLY AND ARE NOT MEANT TO REPLACE A LICENSED PROFESSIONAL. ANY CONSTRUCTION OR USE
OF THE PRODUCT MUST BE IN ACCORDANCE WITH ALL LOCAL ZONING AND/OR BUILDING CODES. THE CONSUMER ASSUMES ALL RISKS AND LIABILITY ASSOCIATED WITH THE CONSTRUCTION
OR USE OF THIS PRODUCT. THE CONSUMER OR CONTRACTOR SHOULD TAKE ALL NECESSARY STEPS TO ENSURE THE SAFETY OF EVERYONE INVOLVED IN THE PROJECT, INCLUDING, BUT NOT
LIMITED TO, WEARING THE APPROPRIATE SAFETY EQUIPMENT. EXCEPT AS CONTAINED IN THE WRITTEN LIMITED WARRANTY, THE WARRANTOR DOES NOT PROVIDE ANY OTHER WARRANTY,
EITHER EXPRESS OR IMPLIED, AND SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING CONSEQUENTIAL DAMAGES.
©2020 UFP Industries, Inc. Deckorators is a registered trademark of Deckorators, Inc. in the U.S. All rights reserved.
68956 U.S. Highway 131, White Pigeon, MI 49099
10944 1/20
www.deckorators.com
Stair Railing Installation Instructions
Prior to construction:
Step 1
Begin by determining where the top and bottom post will be
located. Mark the desired location of the post.
Note: For stair rails that are
in-line with the deck rail, a line post can be used at the top stair location.
For stair rails that are perpendicular the deck rail, an end post is used
to terminate the cable run. The post will be drilled for the stair cable.
Position the post so the fasteners will go into the joists, and make sure the
decking is firmly attached to the joists at the location of the posts. Proper
structural blocking/framing under the decking material is required when
attaching the post to a wood frame deck because decking alone is not
structural framing.
Step 2
Four 3/8” diameter mounting holes are provided on the base.
When final position is determined, mark hole locations and remove the
post assembly. Drill the marked locations through decking and into
structural blocking.
Step 3
Reposition the post assembly with the leveling plate inserted
between the deck and the post base, and aligned with the predrilled
holes. Insert the post fasteners (
NOT INCLUDED
), and partially tighten.
Using a level, adjust the leveling set screws with a 3/16” allen wrench until
the post is plumb. Fully tighten the post fasteners to secure the base to
the deck structure. Note: Recommended 5/16” x 4” or longer lag screws.
Step 4
Finish by sliding a post base trim (optional) over each post sleeve
for a finished look.
Step 5
Measure the distance between installed posts to determine the
length of the top rail. Position the railing on the stairs on top of a spacer
block along the stair nosings. The distance between the post and the
cable spacer should be equal on both ends. Once the railing is in position,
clamp the railing to the posts. Temporarily assemble the swivel brackets.
Position the swivel bracket in location and mark the rail and post. Repeat
for other end of railing. Add 3/4” to the marked location on the railing and
cut to length.
Step 6
Mark locations of the bracket screw holes on the rails. Remove
brackets. Predrill through the rail only, using a 9/64” drill bit. Attach the
front end of bracket to rails.
Step 7
Mark location of the bracket base screw holes on the post. Include
the bracket side cover when determining the center location. Predrill
through the post, using a 9/64” drill bit. Position the base of each bracket
with the bracket cover side facing the stairs, and attach to the post with
two screws.
Step 8
A cable spacer is needed at least every 3 feet (1 is included in the
6ft rail kit, 2 in the 8ft kit). Trim the cable spacer as needed. Attach cable
spacer connectors to the bottom of the rail using included screws. Predrill
using a 1/8” drill bit. Mark the location of the cable spacer on the step
tread and attach the other cable spacer connector to the step tread.
Step 9
Install the railing between the posts by sliding the brackets
together. Attach the side of the bracket with the barrel bolt to secure in
place.
Step 10
Set post caps on each post. Gently tap with rubber mallet to
secure.
Install cable according to the cable instructions.
Post Cap
•
•
Top Rail Bracket
Top Rail
•
2.5-in
Post
•
Post
Base
Trim
•
Cable Spacer
•
•
Cable
< 6''
•
fig. 10
fig. 11
10944
