background image

®

18

Please always adhere to the safety advice given in this manual. Bioethanol fires are REAL FIRES and 
therefore, please use greatest care and common sense when operating them.

DO

DO avoid contact of bioethanol with eyes and skin.
DO keep bioethanol safely and out of reach of children.
DO keep the quality of your room air at an adequate level by opening a window for around 5 - 10 
minutes or by leaving the doors to adjacent rooms open. Should the premises in which the fire is situ-
ated be equipped with an MVHR System (Mechanical Ventilation with Heat Recovery), the room air 
quality will automatically be kept at a high level and no further action should be necessary.
DO avoid contact with any glass and metal parts of your fireplace as these can become hot during 
operation.
DO always adhere to all safety advice given in this manual.

DO NOT

DO NOT smoke when filling the burner with bioethanol as it is – of course – extremely flammable.
DO NOT use any other fuel than bioethanol of at least 96% but max. 97.5% purity.
DO NOT mix bioethanol with other fuels.
DO NOT cover/obstruct any of the ventilation slots of the fireplace. 
DO NOT place any flammable materials or clothes near the fireplace. 
DO NOT place any pebbles or stones on the e-Ribbon Fire™ as these will crack and might cause injury 
or damage to the fireplace.
DO NOT place any ceramic logs or ceramic pebbles on the e-Ribbon Fire™ as they will obstruct the 
ventilation slots in the base plate and change the combustion temperature.
DO NOT install the fireplace outside unless it has explicitly designed for an outdoors application. 
DO NOT attempt to open the housing of the fireplace.
DO NOT modify anything on your custom-made Decoflame bioethanol fireplace.

The made to measure Decoflame bioethanol fireplace is made of aluminium, stainless steel (optional: 
glass), copper, plastics and electronic components. If you wish to dispose of the appliance, please 
adhere to the regional rules and regulations.

You will find, that most parts of your Decoflame fireplace can be recycled.

7. SAFETY ADVICE

8. DISPOSAL AND RECYCLING

Summary of Contents for DENVER E-RIBBON FIRE





















Reviews: