User Manual
UserManual
Digital Weighing Indicator
Digital Weighing Indicator
DIGITAL WEIGHING INDICATOR
- 13 -
DIGITAL WEIGHING INDICATOR
- 12 -
Calibration
Error Indication
Chargeable Battery
1.
Connect the load cell properly and then turn on the indicator and press the [#] key during initial-
ization. It will enter into the calibration mode and calibrate as following:
STEP
OPERATION
DISPLAY
NOTES
1
Press [TARE] for selection of
division
[d X]
Select optional division (1/2/5/10/20/50),
press [#] to confirm
Example: 20
2
Press [TARE] for selection of
DECIMAL POINT selection
[P X ]
Select optional decimal point: 0~3, press [#]
to confirm
Example: 3
3
Set the full range
[FULL]
Press [TARE] for selection of the digit bit; Press
[ZERO] for selection of the digit; Press [#] to
confirm the input of the full range
4
Zero point calibration: Press [#]
when the stable signal is on
[nOLOAD]
Confirm there is no load
5
Full range point calibration:
Press [#] when the value input
is the same as the loaded weight
and the stable signal is on
[AdLOAD]
While inputting the loaded weight,
Press [TARE] for selection of the digit bit; Press
[ZERO] for selection of the digit; when the
input value is the same as the loaded weight
and the digit bit is at the highest bit, press [#]
when the stable signal is on
6
[End]
7
Press the calibration span under
the lead sealing board at the
back of the indicator
It saves the calibration parameter and returns
to the weighing status.
Attention: If you do not press the calibration
switch the parameters will not be saved
2.
FAST CALIBRATION FOR ZERO POINT AND FULL RANGE POINT
Press [#] while it is initializing and it will enter into the calibration mode.
3.
Fast calibration for zero point:
At any point before it displays [nOLOAD], press [FUNC] and it will keep the original division,
decimal point, full range and enter into the zero point calibration mode. Press [ZERO] when the
stable signal is on and it will display [End] and keep the original full range point calibration. Press
the calibration switch under the lead sealing board at the back of the indicator and it will save the
setting and return to the weighing status.
4.
Fast calibration for full range point:
Fast calibration for full range point: At any point before it shows [AdLOAD], press [ACCU] and it will
keep the original division, decimal point, full range, zero point calibration and enter into the full range
point calibration mode. When it is finished, press the calibration switch under the lead sealing board
at the back of the indicator and it will save the setting and return to the weighing status.
EER 1
The AD value is too small when calibrated at full range point.
EER 2
The zero point is out of range when calibrated at zero point.
EER 3
The zero point is out or auto zero range upon starting
EER 4
The input sample quantity is zero when sampling in counting mode.
EER 5
The input weight is zero when full scale calibrated in calibrating mode.
EER 6
The unit weight is less than 0.25e when sampling in counting mode
bAt-lo
Low power
1.
Turn on the AC power and the indicator will charge the battery automatically. If you don’t use the
battery frequently, you should take the battery out.
• Note: red end is +, and the black end is -. Incorrect connection will ruin the indicator.
• Note: The built-in battery should be fully charged before it is used for the first time.
2.
When you turn off the AC power, and push start key the battery will work. When [LouoL] is
displayed it means there is insufficient voltage and it needs to charge.
3.
When you use the battery for the first time, you should charge the battery for 20 hours in order
to ensure maximum battery life.
4.
If you don’t use battery for a long time, you should charge the battery for 10-12 hours every
2 month period to prolong battery life.
