background image

DM-4 Gas/Hydro 

 

 

 

Application Notes, PCM TCP/IP port (WebArm)

 

 

 

DEIF A/S

  

Page 4 of 10 

 

2.  Warnings and legal information 

 

Legal information and responsibility 

DEIF takes no responsibility for installation or operation of the generator set. If there is any doubt 
about how to install or operate the generator set controlled by the unit, the company responsible 
for the installation or the operation of the set must be contacted. 
 
 
 
 
 

Electrostatic discharge awareness 

Sufficient care must be taken to protect the terminals against static discharges during the 
installation. Once the unit is installed and connected, these precautions are no longer necessary. 

Safety issues 

Installing the unit implies work with dangerous currents and voltages. Therefore, the installation 
should only be carried out by authorised personnel who understand the risks involved in working 
with live electrical equipment. 
 
 
 
 
 
 

Definitions 

Throughout this document, a number of notes and warnings will be presented. To ensure that 
these are noticed, they will be highlighted in order to separate them from the general text. 

Notes 

 
  
 
 

Warnings 

 
 
 
 
 
 

The notes provide general information which will be helpful for the reader to bear 
in mind. 

The warnings indicate a potentially dangerous situation which could result in 
death, personal injury or damaged equipment, if certain guidelines are not 
followed. 

Be aware of the hazardous live currents and voltages. Do not touch any AC 
measurement inputs as this could lead to injury or death. 

The DM-4 is not to be opened by unauthorised personnel. If opened anyway, the 

warranty will be lost. 

Summary of Contents for DELOMATIC 4 Series











Reviews: