Operation
DeLaval milking point controller MPCII
94381001.pdf
2006-07-20
F801
Activates LED 1
(don't milk)
F801
Activates LED 1
(don't milk)
F802
Activates LED 2
(dump milk)
F802
Activates LED 2
(dump milk)
F803
Activates LED 3
(treat cow)
F803
Activates LED 3
(treat cow)
F804
Activates LED 4
(separate cow)
F804
Activates LED 4
(separate cow)
F805
Activates LED 5
(feed alarm)
F805
Activates LED 5
(feed alarm)
F806
Activates LED 6
(low yield)
F806
Activates LED 6
(low yield)
F807
Activates LED 7
(milk flow)
F807
Activates LED 7
(milk flow)
F808
Activates LED 8
(remind 1)
F808
Activates LED 8
(remind 1)
F809
Activates LED 9
(remind 2)
F809
Activates LED 9
(remind 2)
F810
Activates LED 10
(remind 3)
F810
Activates LED 10
(remind 3)
F811
Activates LED 11
(remind 4)
F811
Activates LED 11
(remind 4)
F812
Activates LED 12
(Forced high vac)
F812
Activates LED 12
(Forced high vac)
F813
Activates LED 13
(manual)
F813
Activates LED 13
(manual)
F814
Activates LED 14
(bus)
F814
Activates LED 14
(bus)
F815
Activates all LEDs
F815
Activates all LEDs
F831
Activates all segments on MPCII
F831
Activates all segments on MPCII
F850
Activates all LEDs one by one
F850
Activates all LEDs one by one
is deactivated 0.2 seconds after activation!
is deactivated 0.2 seconds after activation!
** Do not forget to change F705, F706 to off if they are connected here.
** Do not forget to change F705, F706 to off if they are connected here.
Test of milk meter:
Test of milk meter:
F901
shows NN.nn
NN = compensation value
(offset), normally 130 (25-231)
F901
shows NN.nn
NN = compensation value
(offset), normally 130 (25-231)
nn = A/D value, empty cup 5 to
56, maximum loaded = 255
nn = A/D value, empty cup 5 to
56, maximum loaded = 255
F903
Opens the MM15's cup for 2 seconds
F903
Opens the MM15's cup for 2 seconds
F910
ISO test
MPCII is set to have high
vacuum and pulsating using
pulsating parameter of main
milking phase.
F910
ISO test
MPCII is set to have high
vacuum and pulsating using
pulsating parameter of main
milking phase.
F911
ISO test at low flow (pre- and post milking phases)
F911
ISO test at low flow (pre- and post milking phases)
F78 – Configuration check
System
This function shows the MPCII place
number.
See adjoining examples.
F79 – Show MPCII's address
System and stand-alone
Pressing F, 7, 9, and ↑ shows the MPCII's
node address for 3 seconds.
76(94)
Summary of Contents for MPCII
