Operation
DeLaval milking point controller MPCII
94381001.pdf
2006-07-20
MPC
MPCII
MPC
MPCII
2 = FI2
2 = FI2
3 = FI5
3 = FI5
F62 ↑ 332 ↑
Parlour configuration
F62 ↑ 332 ↑
Parlour configuration
1 = Herringbone/Midiline
1 = Herringbone/Midiline
2 = Rotary
2 = Rotary
3 = Tandem
3 = Tandem
F62 ↑ 333 ↑
Special MPCII, 0 = No, 1 = Yes
F62 ↑ 333 ↑
Special MPCII, 0 = No, 1 = Yes
F62 ↑ 334 ↑
0 = No EP, 1 = EP100, 2 = EP50, 3 = EP60, 4 = EP70
F62 ↑ 334 ↑
0 = No EP, 1 = EP100, 2 = EP50, 3 = EP60, 4 = EP70
F76 ↑ 711 ↑
Test of EP
outputs
Toggling function. Activates output DC0/V.
F76 ↑ 711 ↑
Test of EP
outputs
Toggling function. Activates output DC0/V.
F76 ↑ 850 ↑
Activates one LED after the other.
F76 ↑ 850 ↑
Activates one LED after the other.
F76 ↑
A function for testing buttons and LEDs.
F76 ↑
A function for testing buttons and LEDs.
F76 ↑ 903 ↑
Opens the MM15s cup for 2 seconds.
F76 ↑ 903 ↑
Opens the MM15s cup for 2 seconds.
F76 ↑ 910 ↑
ISO test Pulsator
ISO-test. MPCII is set to high vacuum and pulsation using
parameter of main milking phase.
F76 ↑ 910 ↑
ISO test Pulsator
ISO-test. MPCII is set to high vacuum and pulsation using
parameter of main milking phase.
F76 ↑ 911 ↑
ISO test Pulsator
ISO-test. MPCII is set to low vacuum and pulsation using
parameter of pre and postmilking phases.
F76 ↑ 911 ↑
ISO test Pulsator
ISO-test. MPCII is set to low vacuum and pulsation using
parameter of pre and postmilking phases.
F76 ↑
If rod reader is connected and there is a transponder in the
reading range, the transponder number is showing on the
displayed as "T xxxx". The transponder number
disappears as soon as the transponder number is
removed.
F76 ↑
If rod reader is connected and there is a transponder in the
reading range, the transponder number is showing on the
displayed as "T xxxx". The transponder number
disappears as soon as the transponder number is
removed.
F91 ↑
Default parameters
F91 ↑
Default parameters
F95 ↑
MPCII boot makes software reset (hot restart). MPCII exits
application program and MPCII starts to run boot program.
To get back press F96 to choose application program.
Choose the program by entering 1 or 2 then F enter. The
MPCII enters application mode. Press F enter to enter
stand by mode.
F95 ↑
MPCII boot makes software reset (hot restart). MPCII exits
application program and MPCII starts to run boot program.
To get back press F96 to choose application program.
Choose the program by entering 1 or 2 then F enter. The
MPCII enters application mode. Press F enter to enter
stand by mode.
F96 ↑
Shows the application program's information.
F96 ↑
Shows the application program's information.
Password 6285
Press F and enter to exit.
Password 6285
Press F and enter to exit.
*"----" means no application program.
*"----" means no application program.
* See picture below.
* See picture below.
* Use enter to step between application program. Press
slot number 1 or 2, and ↑ to start the application program.
* Use enter to step between application program. Press
slot number 1 or 2, and ↑ to start the application program.
F97 ↑
Displays boot program version.
F97 ↑
Displays boot program version.
F98 ↑
Displays application program version.
F98 ↑
Displays application program version.
89(94)
Summary of Contents for MPCII
