background image

 

• 

Use only batteries that are supplied by the manufacturer.

 

• 

Recycle the battery according to local law. Do not incinerate or attempt to puncture  

 

 

or crush the battery.

 

• 

Do not immerse the battery in water or other fluids. Do not expose the battery to  

 

 

rain or snow.

 

• 

Do not expose the battery or tools loaded with battery to direct sunlight. Do not  

 

 

storeor expose battery at temperatures higher than 50˚C (120˚F).  

 

 

Overheating the battery  can result in an explosion or fire.

 

• 

Do not allow direct contact of the battery nodes with metal or  

  conductive 

material.

 

• 

Charge the batteries every 3months, even if the tool is not used, to 

  prevent 

excessive 

 

 

discharging which may damage the battery.

 

• 

Please charge the battery for at least 2 hours before first-time use.

GENERAL  W

ARNING

GENERAL W

ARNING

5

delfast.com

Battery

Model

NACP-400999

Type

Li-ion Battery

Nominal Voltage

7.2V

Capacity

2500mA

Dimension

52.2(l) x 41.9(w) x 85.5mm(h)

Status

Meaning

All LEDs show green

Battery power more than 80%

Two LEDs show green

Battery power between 80% - 60%

One LED show green

Battery power between 60% - 40%

One LED blinks green

Battery power between 40% - 20%

One LED show red

Battery power below 20%

Battery Safety Warning

Summary of Contents for NAC-CN90

















Reviews: