Dell EMC PowerSwitch Z9332F-ON Setup Manual Download

Page: 13 / 16

•

The input circuits are correctly sized for the loads and that you use sufficient overcurrent protection devices.

•

All protective covers are in place.

CAUTION:

Do not power up the switch if you did not install a fan module.

NOTE:

A US AC power cable is included for powering up an AC power supply. You must order all other power cables

separately.

NOTE:

ESD damage can occur if components are mishandled. Always wear an ESD-preventive wrist or heel ground strap

when handling the switch and its components.

Power up sequence

When the switch powers up, the fans immediately come on at high speed. The fan speed slows as the switch continues to boot up.

After switch installation

After you have securely installed and powered on the Z9332F-ON switch:

•

If you are using Dell EMC software, see switch documentation at

www.dell.com/support

•

If you are using third-party software, see ONIE documentation at

www.onie.org

Z9332F-ON Installation

Summary of Contents for PowerSwitch Z9332F-ON

















Search results

Summary of Contents for PowerSwitch Z9332F-ON

Reviews:

Related manuals for PowerSwitch Z9332F-ON

Brands by name

Popular brands

Dell EMC PowerSwitch Z9332F-ON, Setup Manual

Search results

Summary of Contents for PowerSwitch Z9332F-ON

Reviews:

Related manuals for PowerSwitch Z9332F-ON

Brands by name

Popular brands